View Poll Results: Which cam?
TREX
![](https://ls1tech.com/forums/images/polls/bar2-l.gif)
![](https://ls1tech.com/forums/images/polls/bar2.gif)
![](https://ls1tech.com/forums/images/polls/bar2-r.gif)
![](https://ls1tech.com/forums/clear.gif)
70
60.87%
Vindicator
![](https://ls1tech.com/forums/images/polls/bar3-l.gif)
![](https://ls1tech.com/forums/images/polls/bar3.gif)
![](https://ls1tech.com/forums/images/polls/bar3-r.gif)
![](https://ls1tech.com/forums/clear.gif)
45
39.13%
Voters: 115. You may not vote on this poll
TRex or Vindicator
#2
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Vindicator I think you need to flycut the pistons so just be aware of that. Makes amazing power, Upgrade to TFS 215cc heads down the road and be on the border of a 500whp combo with premium boltons.
#7
TECH Resident
iTrader: (11)
Join Date: Jul 2004
Location: Boston
Posts: 987
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
the vindicator is a very close fit, and you can never say for a fact it will fit because the amount the piston comes out of the hole does vary from the factory.
Last edited by ThirdGenLS1; 07-24-2007 at 07:06 PM.
Trending Topics
#8
On The Tree
iTrader: (4)
Join Date: Apr 2006
Location: Winston-Salem, NC
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
There was a guy on here that had .022" PTV clearance with the rev.1 of the Vindicator. Vengeance said that they have seen PTV range from around .030" to about .050". So I would definitely flycut with it. I actually have the Vindicator, but have yet to install it, and I am flycutting. There is a rev. 2 which is like a 113+2 instead of a 112+4, which will give a little more PTV, but I still suggest flycutting.
I would still flycut with the Trex too though. While you're in there, you might as well flycut and mill your heads, to get some of that compression back and keep acceptable clearances.
I would still flycut with the Trex too though. While you're in there, you might as well flycut and mill your heads, to get some of that compression back and keep acceptable clearances.
#12
On The Tree
Thread Starter
iTrader: (7)
Join Date: Jan 2005
Location: robstown tx
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok, my mind's set. Im going w/ the vindicator. Thanks for the advice guys, my buddy just dynoed his A4 w/ a vindicator on a 113lsa, n I must say i was very impressed. Ill let him post up his dyno #s though, I wouldnt wanna ruin it for him. Thanx again guys
#13
Banned
iTrader: (115)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Specialized
be on the border of a 500whp combo with premium boltons.
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
Dont believe all the hype. Yes there are some shop cars that hit the mark but they are few and far between. You need to use all the tricks on the dyno as well and even then some of the dyno numbers posted are pure ridiculous. You can make a dyno read what ever you want.
#14
10 Second Club
iTrader: (11)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Me and Blanco butt heads a lot, but he's right on this one. Check the elevation on those dyno pulls that companies are putting out 500rwhp combos with. Not that Vengeance isn't honest. Just that ANYBODY can be dishonest, and you should check. GET THE FULL FILE FROM THE SHOP THAT SHOWS ALL THE SETTINGS. S&R Racing (a small shop where we dyno sometimes) emails the full 10 page sheet of settings from their SuperFlow dyno so you see that the settings were honest.
#15
Banned
iTrader: (115)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Yep I'm not saying anyone is lying here, I'm just saying not everyone who mimicks the setups gets the same results.
Theres's a lot of tricks to dyno's just as there are tricks to flow numbers. Bigger flow bore being one of them and no one seems to let you know that when you mill a head it changes the flow characteristics.
n4cer we do butt heads but your a car guy and your entitled to your opinion so I'd still have a beer with ya
Theres's a lot of tricks to dyno's just as there are tricks to flow numbers. Bigger flow bore being one of them and no one seems to let you know that when you mill a head it changes the flow characteristics.
n4cer we do butt heads but your a car guy and your entitled to your opinion so I'd still have a beer with ya
![Cheers!!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cheers.gif)
#16
9 Second Club
iTrader: (2)
Join Date: Nov 2004
Location: Amarillo,TX
Posts: 1,205
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by carreras
Ok, my mind's set. Im going w/ the vindicator. Thanks for the advice guys, my buddy just dynoed his A4 w/ a vindicator on a 113lsa, n I must say i was very impressed. Ill let him post up his dyno #s though, I wouldnt wanna ruin it for him. Thanx again guys
#18
FormerVendor
iTrader: (51)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Just to clarify we have broken 500rwhp 4 times.. None of the cars were SHOP cars.. They were customer cars that have since been on a dyno in their hometown and made the same #s are they did here. There are also some individuals out there that have put together some healthy packages that have made 490s to 500s. While it is rare, it can be done and it can be done without cheating a dyno
BTW, I vote for the Vindicator
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
Dont believe all the hype. Yes there are some shop cars that hit the mark but they are few and far between. You need to use all the tricks on the dyno as well and even then some of the dyno numbers posted are pure ridiculous. You can make a dyno read what ever you want.
BTW, I vote for the Vindicator
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
Originally Posted by 99blancoSS
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
Dont believe all the hype. Yes there are some shop cars that hit the mark but they are few and far between. You need to use all the tricks on the dyno as well and even then some of the dyno numbers posted are pure ridiculous. You can make a dyno read what ever you want.