L83 oil pan swap. 1 Attachment(s) Hello. I am working on my L83 swap and have posted information on different aspects of the swap. Here I have pictures of the factory truck L83 oil pan vs. the car LT1 oilpan. As with Gen III and Gen I'VE LS series engines, the Gen V engines L83, L86, LT1, LT4 share the basic block design. This allows the swapping of the oilpan (and other components ) within these engines. The objective is to select the oilpan that best suits your swap application. Here you can see a side by side comparison between the two oilpans. |
L83 oilpan. 1 Attachment(s) Here you can see the new oilpan on the L83 engine. |
L83 oilpan delete external oil line. 4 Attachment(s) This oilpan comes with the external cooler that can be removed and plugged using a delete plate. |
1 Attachment(s) The oil capacity of the car oilpan without the external cooler is to be determined. I do have concerns about the total volume of oil been sufficient to safely operate the engine. The trucks use and external oil cooler similar to the transmission cooler. If an external oil cooler is used it would allow for additional oil volume in the system, plus using the factory stile cooler would extend the live of the engine . I will make my choice towards the end of my installation,. |
5 Attachment(s) The first reason to swap the oilpan is to achieve as much clearance as possible within the 69 CAMARO Subframe. Here I am using ICT Billet Gen V engine mount adapting plates with energy suspension engine mounts. The ICT Billet plates allow for 3 positions, I settled for the center position for the engine mount. The subframe has the factory SBC engine mount towers in the factory location and the L83 almost lines up perfectly. The factory towers on the subframe need to be 1/2 inch lower on both sides. I'll work on modifying my towers and post my results. The engine can drop one more inch from its current location. |
MZRICO do you have a part number for the pan? This is the car version GenV LT oil pan? |
Originally Posted by gthmcty1
(Post 19307975)
MZRICO do you have a part number for the pan? This is the car version GenV LT oil pan? |
Originally Posted by 1975delta88
(Post 19308018)
Is this the Vette Pan or Camaro Pan? The shop chopped my truck pan and it still won't clear steering linkage. I'm looking at the Camaro SS Pan 12639931. I'm going to have to have the shop measure the pan on my 16 Camaro SS to see if it will work. Delta which frame mounts are you using? I had the same issue with the 59 Biscayne as I set the engine in there it practically sat on the steering linkage, in addition the engine mounts and frame mounts would not mate up. I went with actual LS mounts for the frame from CPP and it raised the engine enough to clear the linkage and then some! The factory frame mounts would not line up for s**t! |
Originally Posted by gthmcty1
(Post 19307975)
MZRICO do you have a part number for the pan? This is the car version GenV LT oil pan? |
Originally Posted by mzrico Yes, this particular one is GM 12666386 LT1/LT4 OILPAN. It came with the external cooler. Interesting point is that these oilpans do not have the traditional gaskets we come use to seeing on LS engines. Instead it looks to me that these only use a silicone seal. Thanks for the part number as well! Sorry to hear about your harness in sure once you get it back it will fire right up!! |
Originally Posted by gthmcty1
(Post 19308023)
Delta which frame mounts are you using? I had the same issue with the 59 Biscayne as I set the engine in there it practically sat on the steering linkage, in addition the engine mounts and frame mounts would not mate up. I went with actual LS mounts for the frame from CPP and it raised the engine enough to clear the linkage and then some! The factory frame mounts would not line up for s**t! |
I might have to go with the Camaro SS pan. It looks like it's a lower profile compared to the Vette pan. Will know on Wednesday. |
Originally Posted by 1975delta88 I might have to go with the Camaro SS pan. It looks like it's a lower profile compared to the Vette pan. Will know on Wednesday. |
Originally Posted by 1975delta88
(Post 19309829)
I might have to go with the Camaro SS pan. It looks like it's a lower profile compared to the Vette pan. Will know on Wednesday. |
L83 on a 1969 Camaro Subframe. 5 Attachment(s) I got a few pictures of my work this weekend. With the ICT Billet engine plates (middle position of three possible adjustable ) and the Energy Suspension engine mounts, the L83 almost fits in the stock 69 Camaro subframe without modifications, . I cut and re-welded my factory SBC frame mounts half and inch (2nd and 3rd pics). Also the subframe was notched 3/4''. These modifications locate the engine nicely using the stock subframe holes. The oilpan is protected just above the subframe. The engines balancer clears the front frame crossmember by 1/2". The transmission oilpan does not hang below the subframe. The 6L80e is a few inches longer and wil require a slightly curved crossmember. There are many companies making universal crossmember for LS swaps that can be adapted to the Gen V swaps. The pictures show my results. When I get the body over the frame I will see how the firewall and tunnel may have to be modified. |
That looks good man!!! |
Originally Posted by gthmcty1
(Post 19309831)
Sounds good Delta!! |
Here's my El Camino with the 16 Camaro SS pan. The had to notch the crossmember a little bit, but not by much. I also had to buy the oil cooler separately. It'll just loop into itself once the oil cooler gets installed. https://cimg4.ibsrv.net/gimg/ls1tech...b3a7a5edb1.jpg https://cimg5.ibsrv.net/gimg/ls1tech...f7cbfeae51.jpg |
Originally Posted by 1975delta88
(Post 19328346)
Here's my El Camino with the 16 Camaro SS pan. The had to notch the crossmember a little bit, but not by much. I also had to buy the oil cooler separately. It'll just loop into itself once the oil cooler gets installed. https://cimg4.ibsrv.net/gimg/ls1tech...b3a7a5edb1.jpg https://cimg5.ibsrv.net/gimg/ls1tech...f7cbfeae51.jpg |
Originally Posted by gthmcty1
(Post 19328362)
Man that pan looks like it was made for the frame!!! |
All times are GMT -5. The time now is 04:10 AM. |
© 2024 MH Sub I, LLC dba Internet Brands