HUGE garage PERFORMANCE sale.....
#26
FASTEST ALL MOTOR LS1 IN THE COUNTRY
Thread Starter
iTrader: (4)
Join Date: Dec 2001
Location: Chicago, IL
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mzoomora
How low are you willing to go for the ET drags, and can I pick them up? PM me back.
#27
FASTEST ALL MOTOR LS1 IN THE COUNTRY
Thread Starter
iTrader: (4)
Join Date: Dec 2001
Location: Chicago, IL
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CatchinZs
Is there any way that I could get a link to that TA mount? A pic would work too.
I'm curious how it mounts and works.
I'm curious how it mounts and works.
#28
On The Tree
Join Date: Apr 2005
Location: Carlisle, PA
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CAMN HAWK
the only thing the mount does is: bolt on to the 9" housing after you install the center section, and it then allows you to mount your regualr torque arm that the cars use.
Gotcha...but my concern is its design and whether I think it will be strong enough for my setup. If it was used on the wheel standing monster in your sig then it could work for me.
I found a setup like this....
Seems like this one is used to make your current TA fully adjustable but it doesn't have the provisions to mount to the rear on its own.
#29
9 Second Club
iTrader: (8)
Originally Posted by CAMN HAWK
its the 10% underdrive one. and on the ati the pulley for the a/c is optional i have both pulleys but if you didnt want to run the a/c you dont have to bolt it on the crank pulley.....i used the a/c pulley for it to drive my vaccum pump last season
#30
FASTEST ALL MOTOR LS1 IN THE COUNTRY
Thread Starter
iTrader: (4)
Join Date: Dec 2001
Location: Chicago, IL
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by CatchinZs
Gotcha...but my concern is its design and whether I think it will be strong enough for my setup. If it was used on the wheel standing monster in your sig then it could work for me.
I found a setup like this....
Seems like this one is used to make your current TA fully adjustable but it doesn't have the provisions to mount to the rear on its own.
I found a setup like this....
Seems like this one is used to make your current TA fully adjustable but it doesn't have the provisions to mount to the rear on its own.
#35
FASTEST ALL MOTOR LS1 IN THE COUNTRY
Thread Starter
iTrader: (4)
Join Date: Dec 2001
Location: Chicago, IL
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by exodus
I syill could use the fans, would you go 80 for them if I pick up?
#37
so...i pm'd ya about the fact that it's been 14 days since i sent paypal for the th400 crossmember and it hasn't been delivered yet...then you don't reply to it. what's up? if it's not here tuesday i'll have to make a complaint with paypal. failure to communicate is a great way to do business....
#39
FormerVendor
iTrader: (45)
Originally Posted by ronan
so...i pm'd ya about the fact that it's been 14 days since i sent paypal for the th400 crossmember and it hasn't been delivered yet...then you don't reply to it. what's up? if it's not here tuesday i'll have to make a complaint with paypal. failure to communicate is a great way to do business....
#40
FASTEST ALL MOTOR LS1 IN THE COUNTRY
Thread Starter
iTrader: (4)
Join Date: Dec 2001
Location: Chicago, IL
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
ronan and frost you both have pm's.
not sure what the needed length in a third gen would be....but this ones length is 45 1/8" center to center
not sure what the needed length in a third gen would be....but this ones length is 45 1/8" center to center