LT1 Problem... High RPMS BOGGING!!
#1
On The Tree
Thread Starter
Join Date: Jan 2009
Location: Waco, Tx/ Houston, Tx
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
LT1 Problem... High RPMS BOGGING!!
ok so when i am driving and give it WOT it goes to about 4600 rpm and boggs out like it hit a rev limiter, does it from a stop or on the roll... i got my trans rebuilt.. still does it... took it to a tuner i thought maybe my rev limiter was before my shift point for some reason... nope! so wrong again.... took it to a shop he said fuel pressure regulator... nope!!! i ve spent like 2300 on this damn thing already.... still have the problem.... some say opti spark $250 some say fuel pump $180... UGH!!!!
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
#2
TECH Senior Member
iTrader: (36)
ok so when i am driving and give it WOT it goes to about 4600 rpm and boggs out like it hit a rev limiter, does it from a stop or on the roll... i got my trans rebuilt.. still does it... took it to a tuner i thought maybe my rev limiter was before my shift point for some reason... nope! so wrong again.... took it to a shop he said fuel pressure regulator... nope!!! i ve spent like 2300 on this damn thing already.... still have the problem.... some say opti spark $250 some say fuel pump $180... UGH!!!!
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
#3
On The Tree
Thread Starter
Join Date: Jan 2009
Location: Waco, Tx/ Houston, Tx
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
Yeah i put it on a fuel pressure test and when the key shut off it was at 45 psi. when it turned on and drove around or rev'ed up it dropped to about 38 psi. could that be a problem?
Btw how hard is it to take it off? what do you need?
Btw how hard is it to take it off? what do you need?
#6
On The Tree
Thread Starter
Join Date: Jan 2009
Location: Waco, Tx/ Houston, Tx
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
hey ball ss.... can u give me any reasons why the valve springs??? thanks guys pretty soon i will be changing opti spark along with plugs and wires. if that dont work then fuel pump and fuel filter. if that dont work keep checkin youtube cause am gunna blow this bitch up!!!
BTW thanks guys!!
BTW thanks guys!!
#7
TECH Senior Member
iTrader: (36)
Here is the best deal you will find for a genuine OEM opti:
http://cgi.ebay.com/ebaymotors/95-96...mZ350172822694
Just make sure to remove the cap and thread lock the rotor screws before you install it.
http://cgi.ebay.com/ebaymotors/95-96...mZ350172822694
Just make sure to remove the cap and thread lock the rotor screws before you install it.
Trending Topics
#9
TECH Apprentice
Join Date: Oct 2008
Location: Aurora Ill
Posts: 324
Likes: 0
Received 0 Likes
on
0 Posts
Not trying to hi-jack
I have the same issue. Mine happens later in the rpm band though.
About 5700 or so,no back fire or anything,it just starts to cut out kinda similar to hitting the limiter. My limiter is set at 6200.
My opti is new,plugs are recent and the last I checked the wires were good(recently replaced).
I was gonna wait to trouble shoot though until I install my valve springs to see if maybe its just valva float.
Anyother suggestions?
I have the same issue. Mine happens later in the rpm band though.
About 5700 or so,no back fire or anything,it just starts to cut out kinda similar to hitting the limiter. My limiter is set at 6200.
My opti is new,plugs are recent and the last I checked the wires were good(recently replaced).
I was gonna wait to trouble shoot though until I install my valve springs to see if maybe its just valva float.
Anyother suggestions?
#10
TECH Fanatic
iTrader: (7)
Not trying to hi-jack
I have the same issue. Mine happens later in the rpm band though.
About 5700 or so,no back fire or anything,it just starts to cut out kinda similar to hitting the limiter. My limiter is set at 6200.
My opti is new,plugs are recent and the last I checked the wires were good(recently replaced).
I was gonna wait to trouble shoot though until I install my valve springs to see if maybe its just valva float.
Anyother suggestions?
I have the same issue. Mine happens later in the rpm band though.
About 5700 or so,no back fire or anything,it just starts to cut out kinda similar to hitting the limiter. My limiter is set at 6200.
My opti is new,plugs are recent and the last I checked the wires were good(recently replaced).
I was gonna wait to trouble shoot though until I install my valve springs to see if maybe its just valva float.
Anyother suggestions?
hey ball ss.... can u give me any reasons why the valve springs??? thanks guys pretty soon i will be changing opti spark along with plugs and wires. if that dont work then fuel pump and fuel filter. if that dont work keep checkin youtube cause am gunna blow this bitch up!!!
BTW thanks guys!!
BTW thanks guys!!
Im not one to say, "ITS THE OPTI" but its narrowing down to that...
#12
TECH Apprentice
Join Date: Oct 2008
Location: Aurora Ill
Posts: 324
Likes: 0
Received 0 Likes
on
0 Posts
I hope its not my tranny. That only has about 5k on it!
As far as valve springs getting weak at about 100k,im at 104k on mine. That's why I said ill dig deeper once I swap those. Just seeing if there is anything else I should look at.
Thanks for the tip.
Dale
As far as valve springs getting weak at about 100k,im at 104k on mine. That's why I said ill dig deeper once I swap those. Just seeing if there is anything else I should look at.
Thanks for the tip.
Dale
#13
TECH Regular
iTrader: (3)
Join Date: Apr 2007
Location: Greenville, SC
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
ok so when i am driving and give it WOT it goes to about 4600 rpm and boggs out like it hit a rev limiter, does it from a stop or on the roll... i got my trans rebuilt.. still does it... took it to a tuner i thought maybe my rev limiter was before my shift point for some reason... nope! so wrong again.... took it to a shop he said fuel pressure regulator... nope!!! i ve spent like 2300 on this damn thing already.... still have the problem.... some say opti spark $250 some say fuel pump $180... UGH!!!!
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
BTW no engine code but an low coolant level switch light on...
and it back fires all the damn time!!!
can anyone help me!!!!:bang
THANKS GUYS
Had a similar problem with my 94 A4.. Had my tranny rebuilt and it went away..
I've heard the Lt1 need new valve springs after 100k miles.. I replaced mine recently(112k) and Ill swear my car picked up some...(took me awhile so it prolly was just in my head, lol).
Im not one to say, "ITS THE OPTI" but its narrowing down to that...
I've heard the Lt1 need new valve springs after 100k miles.. I replaced mine recently(112k) and Ill swear my car picked up some...(took me awhile so it prolly was just in my head, lol).
Im not one to say, "ITS THE OPTI" but its narrowing down to that...
#14
TECH Senior Member
iTrader: (36)
The spec for fuel pressure is 43.5psi with the vacuum line disconnected from the fpr, but anywhere from 41-47 is fine. 38psi with the vacuum line connected sounds acceptable, that shouldn't be the cause of your miss/stumble.
I seriously doubt its the springs either.
I seriously doubt its the springs either.
#15
On The Tree
Thread Starter
Join Date: Jan 2009
Location: Waco, Tx/ Houston, Tx
Posts: 199
Likes: 0
Received 0 Likes
on
0 Posts
OK Thanks all that helped. i will be buying a new AC Delco opti spark soon and installing it. should i go ahead and replace plugs and wires also? if so what are the best plugs and wires i could ****** up for my mods?
#19
TECH Regular
iTrader: (3)
Join Date: Apr 2007
Location: Greenville, SC
Posts: 477
Likes: 0
Received 0 Likes
on
0 Posts
whatever you do DONT GET PLATINUM OR IRIDIUM PLUGS! all you need is standard plugs they perform the best and have a stronger spark I use NGK tr55's and tr6's for spray. as far as wires go I have msd 8.5's and don't have any issues with them but I don't think its necessary unless your wires appear to be damaged.