Best place or places to buy ?
#1
Teching In
Thread Starter
iTrader: (1)
Join Date: Sep 2006
Location: Trinity, FL
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Best place or places to buy ?
Hey everyone i haven't been on here for a couple of years but i wanted to get some options on where to purchase a new T-56 & 12 bolt . i am looking at a magnum or super magnum T-56 and a moser 12 bolt bolt in ready. i'd like to buy them both at the same place but i can purchase each at a different company. Thanks in advance for info and help.
#3
9 Second Club
As the moderators will frown at anyone mentioning anyone other than a sponsor....
Bob at Brutespeed for the Moser
https://ls1tech.com/forums/gears-axl...-shipping.html
Tick or RPM or many other of the Sponsors for the trans ( although I bought my converted F-Magnum from DDPerformance )
No doubt there are a few other users here who could supply that too and they might be along if they see the thread.
And just used the Vendor directory ( must admit, it's first time I ever seen it lol )
https://ls1tech.com/forums/vendor_di...hp?category=20
From what I understand the only difference between a Magnum and Super Magnum is the Super has a 40T reluctor for output shaft speed vs the normal 12T.
Super is not a direct F-Swap if that's what you're after.
Although viewing the axle section of the forum, Midwest seem to rate their S60 rear axle very highly and more cost effective than any 9" ?
https://ls1tech.com/forums/gears-axl...-pics-171.html
Bob at Brutespeed for the Moser
https://ls1tech.com/forums/gears-axl...-shipping.html
Tick or RPM or many other of the Sponsors for the trans ( although I bought my converted F-Magnum from DDPerformance )
No doubt there are a few other users here who could supply that too and they might be along if they see the thread.
And just used the Vendor directory ( must admit, it's first time I ever seen it lol )
https://ls1tech.com/forums/vendor_di...hp?category=20
From what I understand the only difference between a Magnum and Super Magnum is the Super has a 40T reluctor for output shaft speed vs the normal 12T.
Super is not a direct F-Swap if that's what you're after.
Although viewing the axle section of the forum, Midwest seem to rate their S60 rear axle very highly and more cost effective than any 9" ?
https://ls1tech.com/forums/gears-axl...-pics-171.html
#4
LS1Tech Sponsor
iTrader: (16)
I recommend a 9 inch over a 12 bolt, reasons why are explained in this link. https://shop.brutespeed.com/Brute-Sp...nformation.htm Bob
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
#6
Teching In
Thread Starter
iTrader: (1)
Join Date: Sep 2006
Location: Trinity, FL
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
I recommend a 9 inch over a 12 bolt, reasons why are explained in this link. https://shop.brutespeed.com/Brute-Sp...nformation.htm Bob
#7
LS1Tech Sponsor
iTrader: (16)
You're welcome, thanks! Bob
__________________
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website
ATI ProCharger and Moser Sales 260 672-2076
PM's disabled, please e-mail me
E-mail: brutespeed@gmail.comob@brutespeed.com
https://brutespeed.com/ Link to website