Description:

For Sale: 347 aluminum ls6 block 3.903 bore, 3.622 stroke 

Stock crank checked and polished 
ARP main studs
Wiseco piston set .024/.028 ring end gap
13.1 Compression ratio, will need to run methanol, E85 or racing gas which ever you prefer.
Scat forged H-beam rods 8740 arp hardware
Melling s296 high volume pump, cloyes hd timing set

Gm mls head gaskets, head studs, Billet oil diverter, King race bearings, Brian Tooley spec'd cam. 247/258 @ .050 .632/.596 lift 111+3 lsa. HYD roller cam. Camshaft specs are in the pictures. Look for it.

Comp 850-16 (older, better comp. Not the new junk). Smith Brothers chromoly 5/16" x .083 wall pushrods, btr trunnion upgraded rockers, comp dual valve springs. Valve springs tested: 160-170 on seat/ 380-390 lift. New stock GM valve covers with -12 AN fittings on each valve cover for oil catch can. Holley valley cover has oil cap to add oil in the engine. Have two different ignition coil brackets: this brackets are for the D514A coils with spacers and the other brackets are for the D585/19005218 "heat sink coils.

New never used 5.5" ATI Damper.
New never used light weight TCI Auto part # 399853LW Forged Flexplate. Total weight is 7.70 lbs.
New never used Moroso oil pan 7 QT minus the oil filter part # 20142
New never used HOLLEY PREMIUM Alternator 150A-Black Part # 197-303, These powerhouses fit ALL Holley accessory brackets, as well as 4th generation F-body, most 1998 thru 2004 GM trucks, and many other applications.
New MSD 6104 LS ignition box to run the ignition coils for carburetor setup. Flash drive with software included.
New never used Power Master Starter. 

706 5.3 Heads, rev stainless 2.00" intake and 1.55 exhaust valves. Heads where ported and polished by a guy from the NASCAR team out in Iowa. Very quality work. Milled to 60 cc. This motor use to go 10.90s in a 3480 lb 4th gen Camaro with a smaller cam and victor junior. Now it has better cam, and a Super Victor, which is brand new. Never used. This motor used to make around 540 crank hp. Should make close to crank 575 hp now. This motor is fresh and Ready to Run right now!

⦁ 24X crank wheel
⦁ Shift RPM 7000
⦁ Rod bearing clearances .002 - .003
⦁ Crankshaft clearances .0025
⦁ Sparkplugs BR7EF/3346 Gap at .045 - .050 for E85 fuel
⦁ K447x3903 piston part number / Comp. Height: 1.300 / Rod 6.125" / Dome 12cc / Pin #: S643 .927 x 2.250 /  0 Deck at: 9.236" / STD Deck height at: 9.240" / Stroke: 3.622" / Avg weight: 492 / Ring set: 3905GFX (x8)
⦁ Scat H beam 6.125" rods
⦁ .051 head gaskets
⦁ LS6 block / low mileage
⦁ Heads milled to 60 cc
⦁ Can handle up to 400 HP nitrous/ No nitrous has never been ran on the engine at this time.
⦁ Yellow engine dolly in the picture is included
⦁ Add your own carburetor, water pump, electronic sensors and ignition coils. These items are not included.

Price is $5500 FIRM. What you see in the pictures is what you get. The location is Huber Heights Ohio 45424. NO TRADES!