LS1TECH - Camaro and Firebird Forum Discussion - View Profile: wrd1972

Notices

wrd1972 wrd1972 is offline

TECH Veteran

Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. 6carmello8
    03-30-2016 08:11 PM
    Hey,
    I just doing a little search and noticed that you're running 4.11's with a t56. Did you notice any significant or any difference between the 3.89 and the 4.11's as far as driving characteristics? I notice that you're putting down about 400whp. Would you keep the 4.11's say you had 450+? Any input would help.
  2. 383whitez
    06-08-2014 01:45 PM
    I saw one of yours posts in the ltx section and noticed you are from KY. I live in Lexington and have a white 95z, it is a hardtop though.
  3. wrd1972
    04-20-2011 09:10 PM
    Length of rod makes no difference. It will only provide a new home position for the piston in th SC and the throw will be the same. Clearly its a release problem and an aftermarket adjustable SC is an option or replace the disk with a non marcel type disk. See my comments in that thread on marcel disks.
  4. tylerwerrin
    04-20-2011 08:40 PM
    Hey Wrd,

    I saw a post you made a few months back regarding slave cylinder mods for an LT1 t56. i'm having what i think to be the same problem as the guy's thread you posted on.

    right now, my master only displaces 5.38cm^3 of fluid. its a small bore (1.9cm) and I only have around 1.9cm of stroke. I'm working with a slave cylinder from a 1990 camaro. I ended up blowing out the end of my other slave while bleeding it.

    When i worked out the math, I was only getting like 1.06cm of movement, so I'm off by about 1.5cm to disengage the clutch. Since my pedal pressure is already quite high, i dont want to just go with a larger bore master -- what if i just made a new slave cylinder rod that was 1.5cm longer (or slightly longer)? wouldn't that solve the problem?

    I don't know what the stock slave's rod length is (on a 1993 camaro LT1) so i'm kinda out of luck on that. for all i know the rod in a 1990 camaro slave is shorter than the t56, which might make sense.

    what do you think?
  5. qwerty1
    01-29-2010 12:53 PM
    Hi I saw your post about clutch drag on a LT1, not shifting into gear when started. Was hoping to ask a few questions about your experiance with that. I have a 1995 trans am 6-speed 355 just rebuilt with a new autozone clutch installed in it. When I bought the car It had the same clutch brand just used but didn't shift very smoothly and reverse was even harder to get into (didn't work propperly when I bought it). After the new clutch/pilot was installed shifts with out clutch pushed in (same as pushed in) with car off but when started no shift at all. I have the car on jack stands and if I start the car in gear it starts and rear wheels don't spin unless I let up on the clutch peddel half way up then the clutch engages wheels spin. Is this a clutch problem installation problem hydrlic problem? Any info would be greatly appreaciated.
  6. MadHammer_dot_com
    12-03-2009 09:26 PM
    Hi, we are the OEM manufacturer of the exhausts for the Dale Earnhardt Camaro, Berger Camaro and other high performance Camaros. We saw and liked your Project Bad Ass True Dual system that you made and would like to discuss producing it. We are located in Xenia, OH. If you are interested, you can contact us at [email protected] We have been building systems for years (founded 2002) and selling them thru an exclusive retailer. That exclusivity agreement recently expired and we are building a brand "Mad Hammer Performance Exhaust" around that system to help continue the success that we have had in the past while also expanding our product line. Our business name is Ken-Rich Specialities, located in Xenia, OH and our "Under Construction" website is www.MadHammer.com

    Looking forward to talking with you,
    Steven Tolle

About Me

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 10-26-2018 11:16 AM
  • Join Date: 03-21-2006

Friends

Showing Friends 1 to 5 of 5

Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.