Roller 355 SBC S/B,solid roller parts & SBC/LT1 inturnals
#1
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Jan 2005
Location: Scottsdale Az
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
Roller 355 SBC S/B,solid roller parts & SBC/LT1 inturnals
I have a bunch of SBC/LT1 parts for sale
I have a set of used SRP forged pistons; j/e rings and pins less then 200 miles on them.
P/n srp-138086 and a matching set of j/e rings. These were in a motor that ate a cam there are pock marks on the side of the skirts. Nothing that would affect the motors performance, only the esthetics of the piston. I can and will provide pictures. I have seen people trying to sell far worse for more.
Specs: 4.040 bore 5/16th top 5/16th second and 3/16th oil. Pressed or floating pin and a 6.0 inch rod with a 3.48in stroke.
$300.00 Shipped OBO. New = $460 (pistons) $140 (rings) from summit.
I have a set of solid roller lifters – by comp cams- minus one lifter and cross bar also a matching set of pushrods-by comp cams- minus one. Less then 200 miles
Specs: fit standerd lifter bore sbc/lt1 all rollers are fine. Not sure of the part numbers on these. But looked at prices and its about 40 bucks average for a lifter and cross-bar and 10 for a pushrod form comp. A new set of bottom barrel S/R lifters is $350 not including push rods.
I will do $250 shipped OBO for lifters and pushrods. This set was like 500 new a few years ago.
I have a complete Roller Sbc short block either assmeled or un.
Its an 87-99 4-bolt main roller block that’s .040 Has been vated, line honed and magnafluxed. It has a balanced rotating assembly including a ZZ4 steel crank that’s 20/20 under. Matching Clevite 77 bearing, p/n cb-663-p-20 (rod) ms-909-p-20(main) and cam bearings. Rods are eagle SIR I beams in 6.0 inch form with pressed pins, P/N esp-6000bplw attached are SRP 4.040 11cc dome pistons pn.srp-140679 with matching J/E pro seal rings pn.0532-J100F8-40305. melling HV pump and bolt on pick up for the deep sump pan. TCI, SFI flex plate and SFI balancer. All machine work done by B & B Machine In Mesa AZ (have receipt’s) There’s a lot in this
I can assemble this or you can. It’s your choice?? Stating at $1750 OBO I can strap this to a pallet to ship.
Buyers’ pay all shipping charges (except where noted) and a 2.9999% handling Fee for PayPal.
I would like to sell this locally but who ever wants it wants it. Pictures can be e-mailed just lmk. If you are local send me a p.m. and I will shoot you my number so you can come look at this.
Eric
I have a set of used SRP forged pistons; j/e rings and pins less then 200 miles on them.
P/n srp-138086 and a matching set of j/e rings. These were in a motor that ate a cam there are pock marks on the side of the skirts. Nothing that would affect the motors performance, only the esthetics of the piston. I can and will provide pictures. I have seen people trying to sell far worse for more.
Specs: 4.040 bore 5/16th top 5/16th second and 3/16th oil. Pressed or floating pin and a 6.0 inch rod with a 3.48in stroke.
$300.00 Shipped OBO. New = $460 (pistons) $140 (rings) from summit.
I have a set of solid roller lifters – by comp cams- minus one lifter and cross bar also a matching set of pushrods-by comp cams- minus one. Less then 200 miles
Specs: fit standerd lifter bore sbc/lt1 all rollers are fine. Not sure of the part numbers on these. But looked at prices and its about 40 bucks average for a lifter and cross-bar and 10 for a pushrod form comp. A new set of bottom barrel S/R lifters is $350 not including push rods.
I will do $250 shipped OBO for lifters and pushrods. This set was like 500 new a few years ago.
I have a complete Roller Sbc short block either assmeled or un.
Its an 87-99 4-bolt main roller block that’s .040 Has been vated, line honed and magnafluxed. It has a balanced rotating assembly including a ZZ4 steel crank that’s 20/20 under. Matching Clevite 77 bearing, p/n cb-663-p-20 (rod) ms-909-p-20(main) and cam bearings. Rods are eagle SIR I beams in 6.0 inch form with pressed pins, P/N esp-6000bplw attached are SRP 4.040 11cc dome pistons pn.srp-140679 with matching J/E pro seal rings pn.0532-J100F8-40305. melling HV pump and bolt on pick up for the deep sump pan. TCI, SFI flex plate and SFI balancer. All machine work done by B & B Machine In Mesa AZ (have receipt’s) There’s a lot in this
I can assemble this or you can. It’s your choice?? Stating at $1750 OBO I can strap this to a pallet to ship.
Buyers’ pay all shipping charges (except where noted) and a 2.9999% handling Fee for PayPal.
I would like to sell this locally but who ever wants it wants it. Pictures can be e-mailed just lmk. If you are local send me a p.m. and I will shoot you my number so you can come look at this.
Eric
Last edited by 1dirtybird; 12-31-2009 at 06:06 PM.
#2
TECH Apprentice
Thread Starter
iTrader: (7)
Join Date: Jan 2005
Location: Scottsdale Az
Posts: 392
Likes: 0
Received 0 Likes
on
0 Posts
I left out that the compression ratio's. With the 11cc dome pistons are between 12 and 14.7 to 1 depending on what size chambers and gaskets u use. The bottom end should be good for about 600 hp
Eric
Eric