THE OFFICIAL: Pay it Forward (free stuff)
01-23-2012, 07:08 PM
#1021
TECH Veteran
iTrader: (30)
Join Date: Jan 2003
Location: Texarkana, Tx
Posts: 4,391
Likes: 0
Received 0 Likes
on
0 Posts
Category: Drivetrain
Price: $0
Part Fits: 93-02 Chevrolet Camaro
Location (State): MI
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LT1/LT4
LS Engine?: Fits LS Engine
01-26-2012, 01:31 AM
#1022
have this for trade
T-top not sure which side believe is passanger
MAF Sensor, not sure if LT1 or LS1
MAF Sensor in housing for ls1 (think is the same for LT1)
OEM tips off a z28 black square shape
thats all i can remember but im sure i have some stuff laying around
Looking for lowering springs or some sort of springs thanks
T-top not sure which side believe is passanger
MAF Sensor, not sure if LT1 or LS1
MAF Sensor in housing for ls1 (think is the same for LT1)
OEM tips off a z28 black square shape
thats all i can remember but im sure i have some stuff laying around
Looking for lowering springs or some sort of springs thanks
01-29-2012, 08:27 PM
#1024
TECH Fanatic
I hope some one wants these parts...
Bose cassette player
2 Bose door speakers with out apms
complete rear Bose subwoofer
All out of 93 z28 I no longer own.
all in good working order.
shipping is all they will cost.
Bose cassette player
2 Bose door speakers with out apms
complete rear Bose subwoofer
All out of 93 z28 I no longer own.
all in good working order.
shipping is all they will cost.
01-29-2012, 08:55 PM
#1025
I have one.single ls valve cover and a ls tb cable style it the ride either are yours.
I need a stock set of ev1 Injectors and badly a lq4 rod and piston press pin style. Please pm
I need a stock set of ev1 Injectors and badly a lq4 rod and piston press pin style. Please pm
02-04-2012, 09:31 AM
#1031
TECH Apprentice
iTrader: (1)
Join Date: Apr 2010
Location: Newark,DE
Posts: 310
Likes: 0
Received 0 Likes
on
0 Posts
I have a few things I could trade as well.
26lb Accel injectors with about 500 miles on them
LT1 MSD Cap
MSD Wire set with about 500 miles on them. One wire would need to be cut back and the boot replaced, the wire cracked close to the boot.
What I need
Lt1 Camaro upper dash pad
lt1 grey charcoal t-top headliner
lt1 camaro drivers side/steering wheel airbag
M6 Center console trim around the shifter. I need both the small shift boot plastic ring AND the larger plastic piece that holds the entire shift boot in place.
M6 center console ashtray lid
Located in northern delaware if anyone is within driving distance for the larger parts.
Also have a metal black shift ****. its ball shaped and has Z28 etched in silver on it. Would like a leather wrapped one.
26lb Accel injectors with about 500 miles on them
LT1 MSD Cap
MSD Wire set with about 500 miles on them. One wire would need to be cut back and the boot replaced, the wire cracked close to the boot.
What I need
Lt1 Camaro upper dash pad
lt1 grey charcoal t-top headliner
lt1 camaro drivers side/steering wheel airbag
M6 Center console trim around the shifter. I need both the small shift boot plastic ring AND the larger plastic piece that holds the entire shift boot in place.
M6 center console ashtray lid
Located in northern delaware if anyone is within driving distance for the larger parts.
Also have a metal black shift ****. its ball shaped and has Z28 etched in silver on it. Would like a leather wrapped one.
Last edited by GreenBlood55; 02-04-2012 at 09:37 AM.
02-04-2012, 01:47 PM
#1032
Staging Lane
iTrader: (3)
Join Date: Jun 2010
Location: Woodhaven, Michigan
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
Greenblood, is that MSD cap and wire set good for a full LT1 wire swap or are there parts missing? Is that the one that's going to need an exciter box?
If so I've got my old Hurst **** sitting in my glove box.
Some palm wear as usual so it's not perfect (pulled at 35K miles but it was on there for 11 years). Not going to use it anymore because what I thought would be a cumbersome **** turned into one bitchin piece of work:
And yes, I can make them.. I just don't have spare SE *****/buttons and threaded portions (IE autozone *****) to work with ATM.
Depends on what RPO your speaker system is.
I doubt it'll hook up though, mine had to be NOS AC Delco Monsoons otherwise I'd have gone with something else if I hadn't found the NOS ones.
If so I've got my old Hurst **** sitting in my glove box.
Some palm wear as usual so it's not perfect (pulled at 35K miles but it was on there for 11 years). Not going to use it anymore because what I thought would be a cumbersome **** turned into one bitchin piece of work:
And yes, I can make them.. I just don't have spare SE *****/buttons and threaded portions (IE autozone *****) to work with ATM.
I doubt it'll hook up though, mine had to be NOS AC Delco Monsoons otherwise I'd have gone with something else if I hadn't found the NOS ones.
02-04-2012, 06:09 PM
#1035
Staging Lane
Join Date: Mar 2008
Location: Savannah, GA
Posts: 65
Likes: 0
Received 0 Likes
on
0 Posts
I have a set Front and Back Eibach Sportline springs. Came with the car when I got them, and have about 5k miles on them. Yours if you want them, they have been in the garage for about 3 years.....collecting dust.
WHAT I NEED:
2:73 gears for the rear.... after I get those, i will give away the 3:73 that are installed on my 99 TA. I have a series 2 carrier.
WHAT I NEED:
2:73 gears for the rear.... after I get those, i will give away the 3:73 that are installed on my 99 TA. I have a series 2 carrier.
02-04-2012, 11:23 PM
#1038
anybody have the door handle bezel for the pass side? mine cracked :/ have something i could trade, just let me know if anyone's interested in anything..
edit: forgot to mention is, mines an 02 so the bezel needs to be black. thanks
edit: forgot to mention is, mines an 02 so the bezel needs to be black. thanks
