Stand Alone/TH400 SWAP/ WCCH 245cc heads/ Solid Roller Lifters Cam
06-10-2010, 10:57 PM
#1
Teching In
Thread Starter
iTrader: (12)
Join Date: Jul 2009
Location: Dallas, TX
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Stand Alone/TH400 SWAP/ WCCH 245cc heads/ Solid Roller Lifters Cam Category: Engine - Intake/Fuel
Price: $100
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, Corvette, 04-06 Pontiac GTO
Location (State): TX
Item Condition: Brand New
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Non-LS Part
Nitrous Outlet Stand Alone Fuel System $550
-Battery relocate Cell
-Intank Walbro 255 lpm
-Aeromotive Fuel Pressure Regulator
-Fuel Pressure Saftey Switch
-Fuel Pressure Gauge
-6an Fuel Lines
TH-400 SWAP
Th400 Rebuildable Core - $300
ATI 10” Treemaster torque convertor, just rebuilt by ATI. 4000 stall setup for small shot of nitrous, will work well on NA motors as well. $350
TCI Flexplate LS1/TH400 - SOLD
TCI outlaw shifter -SOLD
UMI tubular cross member for TH400 - $150
B&M trans cooler with braided lines - $125
Lokar flexible dipstick - $75
PST 3.5 inch 1200 HP driveshaft - $400
- Correct length for the TH-400 and 9 inch
- Also should be the right length for most other combos.
- Has 1350 U joints
RCI Tranny Blancket - $100
IF YOU WANT THE WHOLE TH400 PACKAGE I WILL CUT YOU A DEAL...
480rwhp Head Cam Package - SOLD
-Patriot LS6 Stage 3 Heads w/650 lift springs
-2.08 / 1.6 Stainless Valves
-10k miles but fresh out of machine shop(cleaned and valve job)
-Comp Cam 238/240-Dur 605/609-Lift 112LSA
-Comp R Lifters
-Comp Hardened Pushrods
-Car Made 480rwhp with 370CI, LS6 intake, through M6
QA1 w/Springs - Sold
Accufab 4500 TB - Sold
Morel Solid Roller Lifter Set-- part# 184-4737-SR.....$400
(Pictures upon request)
Custom cam from West Coast Cylinder Heads- solid roller- 252/258 .641 .652 110LSA.....$300
(Pictures upon request)
Hardened chromoly push rods length matched to cam and solid roller lifter combination....$100
(Pictures upon request)
WCCH custom machined Edelbrock 245 aluminum heads. Complete with patriot dual extreme (upgraded) springs (ARP headbolts included)....$2400
Peak intake flow: 330cfm @ .600"
Exhaust: 260cfm @ .600"
Milled to 59cc chamber size
Harland Sharp 1.7 ratio shaft mount Adjustable rockers- $400
^^I Will combine the rockers and heads above for a total of $2600
All these parts (WCCH heads, Solid lifter/cam, Harland Sharp, pushrods ) are not NIB But thay have never been run. All have been lubed and assembled into a 370 long block, wrapped in plastic and stored in a garage. Feel free to make any offers you are comfortable with.
Last edited by LoudGM; 06-17-2010 at 11:54 PM.
