parting out car parting out car and parts. lost interest and would rather be 30 miles offshore fishing instead of at the drag strip. nx nitrous kit 2 stage shark nozzles 300 total shot. 20lb bottle NX 900.00 tubular k-member spohn for power steering200 without arms with arms upper and lower 600 K-member SOLD with tubular arms upper and lower.SORRY GUYS NOT BMR SPOHN panhard rod adjustable 75 TH400 with coan th400 manual valve body race clutch bands H.D. INTERMEDIATE SPRAG-34 ELEMENT 900 12 bolt strange rearend 4:10 gear set from them. upgraded race axles and bearings 1000 SOLD 385 CI 4 bolt splayed main cap LT1. motor is fresh built and has not been cranked yet (still at machine shop) mls head gaskets complete 5900. callies dragon slayer crank 3.750 600 , compstar 6inch rods 450, je nitrous pistons .040 550 ADDEDdiamond nitrous pistons .030 for 6 inch rod 300 Spohn tubular TA (BMR BRAND WAS MY MISTAKE) 200 cheetah shifter th400 turbo shifter 150 new DR 325/50r15's never ran . mickey thompson et street 200 each or 400 both. AI trickflow 210cc heads and custom cam 245/249 .610lift cam and heads 3000 GM lifters new and 1.6 NSA comp rockers. lifters 50 rockers 200 rockers sold electric water pump meziere only a few hours on it (maybe 15hrs if that) FJO progressive nitrous controller. can control both stages 150 telstar rims. i know 3.5 width on a 15, with the correct spacer for fbody cars. the rears are 10.5 or close (if someone is interested i can go look at the shop and take some pics) stand alone fuel system (low pressure) with pump and reg and fuel cell. it's not a custom cell for the f-bodies, i made space for it. low impedance injector driver and 60lb injectors ASM mono blade throttle body 300 hooker long tubes recoated with the gray high temp coating. 200 LTCC coil over plug setup 200/ sold canton road race pan 242t i think was the part number 200 trans cooler ADDED rear lower control arms, Spohn non adjustable SOLD ADDED factory larger than stock SS front sway bar 50 ADDED factory SS rims with new nitto drag radials on rear 300 and RR compound on the fronts 300 ADDED 4 inch cowl hood 100 ADDED 1996 Z28SS number 1053. It has never been wrecked. The nose piece is aftermarket. The paint is in good shape. The parts are coming off of it. the interior is out of the car and has been sold over a year ago. Its a t-top car. The vin is clean and clear. i will throw in the spider webs under the car for free. these parts will not be sold at dirt cheap prices. so any body saying "ill give 500 for the nitrous kit and controller" that's worth over 1,000, need not post. these are not cheap or trash parts. the last builder of the motor had to much clearance in the wall with the .030 bore and i had to rebuild with a .040 bore. if you want the machine shop number i'll give it to you. they are known locally for building motors that stay together under boost and nitrous. (ex. a friends mustang running 5.70's (1/8th mile) on a 76mm turbo on a true 10.5 tire with a dart small block in the low 300 CI and is very streetable. as in he can drive it 2 hours away and drive it back without issue.) there was just way to much blowby. the tranny has not been used since rebuild. some items can be shipped but buyer pays shipping |
pm sent on stand alone system and torque arm |
electric water pump meziere only a few hours on it...How much and whats the part number? |
prices? |
Originally Posted by beavis
(Post 16770371)
electric water pump meziere only a few hours on it...How much and whats the part number? 150.00. with with relay. if you want my modded fan shroud with it add another 100.00. you will have to flip and fan cover and trim it with a cutter for a good fit. |
Originally Posted by 1961ba427
(Post 16770409)
prices? |
1.6 rockers and the LTCC set-up |
How about the Canton oil pan? does it come w/ the pickup? |
Originally Posted by 1961ba427
(Post 16770586)
1.6 rockers and the LTCC set-up rockers for 200 http://www.jegs.com/i/Comp-Cams/249/...70#moreDetails i have half a set of 1.5's i will throw in also for the same price. |
Originally Posted by flyinZ
(Post 16770645)
How about the Canton oil pan? does it come w/ the pickup? |
Got a y pipe ? |
Originally Posted by Jadedbird
(Post 16770890)
Got a y pipe ? |
tried to update some of the items with prices and added another set of nitrous pistons |
added a few more items i have a laptop for LT1EDIT and pcm can go with it. 200 for both. laptop has a new battery in it. |
http://i87.photobucket.com/albums/k1.../pics012-1.jpg http://i87.photobucket.com/albums/k1.../pics010-2.jpg i have requests coming in from email, text and PM on here. can all of you guys please post questions and requests in here to help me keep it all together. thanks Jason S please post up the items you hit me up in the texts about. Mason please post up your items you requested. if some guys inquired about parts and still want info or whatever please post. I do honor first come first serve and will hold items for a little while, to help people out. money now is nice but i am not broke so i am not desperate lol. good luck to all and have a great day. T minus 48 hours and i will be out of reach until monday. "bite you damn 40lb king bite, daddy needs some new reels and rods for blue fins this winter.":D |
Can you PM me a total shipped and Paypaled on the Canton pan and pick up to MI zip 49323? Thanks |
Originally Posted by jasonisdn
(Post 16775708)
http://i87.photobucket.com/albums/k1.../pics012-1.jpg http://i87.photobucket.com/albums/k1.../pics010-2.jpg Jason S please post up the items you hit me up in the texts about. T minus 48 hours and i will be out of reach until monday. "bite you damn 40lb king bite, daddy needs some new reels and rods for blue fins this winter.":D |
Originally Posted by Revson
(Post 16775836)
Can you PM me a total shipped and Paypaled on the Canton pan and pick up to MI zip 49323? Thanks |
Originally Posted by 1961ba427
(Post 16775848)
I inquired today about the k-member & 12 bolt. I bought the rockers and LTCC yesterday. If they aren't biting, you can always take some TNT. :D |
Originally Posted by jasonisdn
(Post 16776209)
241.63 by the looks of it. using usps from zip 27244 |
All times are GMT -5. The time now is 08:07 AM. |
© 2024 MH Sub I, LLC dba Internet Brands