FS PRC 5.3L Stage 2.5's, PICS ADDED Monster lvl 1 Twin, Racetronic 42lb inj
#1
FS PRC 5.3L Stage 2.5's, PICS ADDED Monster lvl 1 Twin, Racetronic 42lb inj
Category: Engine - Intake/Fuel
Price: $12345
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO
Location (State): MN
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
LS Engine?: Fits LS Engine
SHIPPING is APO through USPS NOT international. :-)
SOLD! (if slow boat is okay) Tentatively sold but no funds yet. For sale are my PRC 5.3L Stage 2.5 heads. 8k miles. .650 lift dual springs. No leaks or worn guides. Rollers with shimmed wipe were used.
SOLD! Monster lvl 1 Twin Is out of the car and on it's way to Monster to be checked!
SOLD! TSP 228r 114 LSA. Again 8k miles no damage. Will also trade for above cam.
SOLD! Racetronic 42lb @ 58psi injectors. Fat body LS1 length. 5k miles no leaks.
SOLD! EV6 to EV1 adapters. Allows LS1 style injectors to work on newer motors.
SOLD! TSP 7.425" pushrods. Perfect for the smaller base of the TSP 228r.
I also have some 241's with 22k on them I'll take $100 plus shipping.
I'll get some pics up tonight.
I do have paypal.
Last edited by Exidous; 02-17-2014 at 03:01 AM. Reason: Pics and vid added
#3
In a continuation of my "demod" I still have a LS7 clutch laying around and am going back to it. This means my Monster lvl 1 TWIN is also for sale. The flywheel and special TOB will be included. Asking $900+shipping. The clutch has zero chatter and about 4k miles on it. If I get some serious inquiries I'll remove it and get some pics but again it is installed on the car.
Trending Topics
#11
NEW LOWER PRICE ON THE PRC HEADS! $880. + half of the shipping.
I notice after looking closely that a couple of the valve stem ends were worn by the roller rockers. I must have gotten a bad batch. So the price is now lower to reflect the damage.
Edit: Just took a closer look. It's all cosmetic but I'll keep the price where it's at. You can see the wipe pattern on a few of the intake stems(none of the exhaust).
I notice after looking closely that a couple of the valve stem ends were worn by the roller rockers. I must have gotten a bad batch. So the price is now lower to reflect the damage.
Edit: Just took a closer look. It's all cosmetic but I'll keep the price where it's at. You can see the wipe pattern on a few of the intake stems(none of the exhaust).
Last edited by Exidous; 12-09-2013 at 03:17 PM.
#16
I have not.
http://www.texas-speed.com/p-247-rac...injectors.aspx
These are the exact injectors. They list as 37lb at 42psi or 3 bar. I'm starting to think they are closer to 50lb injectors at 4 bar. My setup below had them at 62% duty cycle.
I will note one of them is missing a top o-ring.
http://www.texas-speed.com/p-247-rac...injectors.aspx
These are the exact injectors. They list as 37lb at 42psi or 3 bar. I'm starting to think they are closer to 50lb injectors at 4 bar. My setup below had them at 62% duty cycle.
I will note one of them is missing a top o-ring.
Last edited by Exidous; 12-11-2013 at 02:41 PM.