Fresh Turn key ls1, LQ4.. 4L60.th350 and lots of fbody parts
#1
Fresh Turn key ls1, LQ4.. 4L60.th350 and lots of fbody parts
Category: Accessories
Price: $1234
Location (State): NY
Item Condition: Used
LS Engine?: Fits LS Engine
Call or text 716-428-1674
Thanks,
Adam B.
Hello, I have a few parts from a 2000 SS SLP Camaro as well as some LS based engines & parts.. Most Fbody parts are for the 98-02 but I do have some LT1 93-97 parts.. If I dont have what your looking for I may know someone who does, Thanks
LQ4 Complete TURN KEY pulled from a wrecked 2003 2500 Silverado with just under 200,000 miles. Ran great when pulled. DBC Throttle Bodie
Includes
-Full harness, ECU & Fuse box
-All sensors, Coils, Electronics
-Complete Front Accessories (Truck Style)
*Alternator
*Water Pump
*Powersteering Pump
.... All brackets, hardware, pullys & tensioner's.. Even includes fan & starter with solenoid & flexplate.
Ready to Run
$650.. Can deliver or possibly even ship for the right price.
Ls1 TURN KEY minus the intake under 6,000 miles.
Block cleaned
Re-ringed
Honed
Mains align honed
Crank polish
New Main, Rod &Camshaft bearings
... Crosshatch was supposedly in very nice shape when the engine was pulled.
243/Ls6 heads.. Believe they are sodium filled valve's
Milled .010" or roughly 1.5cc less than stock
PAC valve spring kit. (Behive style)
New GM replacement Rockers & Stands
LS2 lifter trays
Ls7 lifters
LS7 Camshaft
Front cam sensor cover
Melling oil pump
New pic up
More im missing im sure...
Comes with all the needed sensors, coils..ect..
Complete unhacked Harness & ECU(tunned for this engine) from a 2000 A4 SS
All F-Body:
-Alternator
-Power Steering pump w/reservoir, lines, factory heater/cooler thing.. Have aftermarket remote reservoir's I could include..
-Water Pump
-Tensioner
-starter (& battery cable's)
-A/C compressor (COLD A/C)
-All the needed brackets , hardware, pulleys... Even belts
New Poly motor mounts with clamshell's
Flexplate.. Fbody Pan ...even egr if you want
I have videos of the car running, driving..walk arounds..
It had a F.A.S.T. LSX 92/92 on it that has since sold. I may have a stock LS1 intake I can include... Or a LM7 Truck Intake
$2,500 not a penny less. Dont waste my time with offers. I may ship or deliver for an extra cost
I do not have any paperwork on the rebuild... I purchased the car from ohio.. the last owner had the work done somwhere local there, that being said you can see its clean.
Fresh Ready to go 4l60e that was aslo form the car.. Rebuilt with a very nice deep finned pan, stock stall replacement converter... All TCI internals, includes NEW Poly mount, crossmember, NEW oil cooler & trans lines..
I belive I have the summit recipts for the parts purchased for the trans.. It was done at the same time as the engine.. Also has poly mounts
$550... Also can ship or deliver for an extra price.. Or include it with the engine for $3,000 FIRM.
Car was well cared for.
35psi oil prs at at hot idle with 5/30
Please read before asking questions
LM7 Intake Manifold from a 2007 5.3 Trailblazer with 105,000miles, comes loaded with rails, injectors, any sensors that plug into it.. Intale bolts and gaskets
Also DBW Throttle Bodie
$110
Coil Packs full set(8) with clean rust free brackets, harnesses & hardware.
The desired "Truck" Coils, with the aluminum cooling fins.
$150... Have 2 sets
Newer style "Truck" Coil Packs.. Full set also harnesses, rust free brackets and hardware
$75
GM Truck Valve Covers
$50 set
GM Fbody Valve Covers
$50 set
799/243 Cylinder Heads, off the same 5.3 as the intake manifold so they are NOT Sodium filled valves. 1 head is still completely assembled with the springs still installed
The other has had the springs removed but will include everything bedsides locks & retainers
$350
Complete Front Accessorie Drive. F-Body, All newer parts replaced recently
Complete starter, waterpump, alternator, power/steering, A/C all brackets & hardware.. Balancer ect.
$450obo
GM Factory rocker arm sets with bolts & rails.. Set of 16 all in good condition less than 80k
$90obo
NEW GM LS3 offset intake rockers(8) & standard exhaust rockers(8) 16 total
NEW GM LS3 rocker arm stands
Used GM rocker arm bolts
$220obo
Used standard rockers or NEW LS3 rockers with high quality BUSHING Style Trunion upgrade. Not the un-reliable Comp needle bearing style. Bronze bushings 360degrees of oiling surface.. Oil grooves machined into trunions.. Very nice upgrade & well worth it. Best rocker set up if I had to choose.. Very light
Stock Standard GM with upgrade installed (with stands&bolts) $350
NEW LS3 GM with upgrade installed (includes stands & bolts) $450
NEW GM LS6 Valley cover. Only Factory cover to help fight the crankcase issues that these engines face.
$75obo
Custom built widage tray made to ACTUALLY cut down windage... Also made too clear stroker set ups
$125
2 sets of Long Tube Headers.. 98-02 Fbody. Also can be used in 78-88 G-bodys with slight modifications both 3" collectors
NEW Texas Speed Stainless 1-7/8"
$250
Used Hooker Super Competition Coated 1-3/4" TUNED primarys..
$250 ($800+ New)
NEW GM Performance MLS Header Gaskets, Stainless steel header bolts & almost new O2 Snesors can be thrown in with either for $300
Y-Pipe 98-02 Hooker Super Competition Y-pipe with 2 stainless steel high flow catalytic converters.. Also includes new o2 sensors..
$250
Borla Cat back exhaust. Stainless steel good shape, has a QuickTimePerformance electric cut out designed for the borla set up only. Includes all hardware, tips, clamps, cut out, switch & wiring...
$500
All Exhaust Components are in good condition
Aluminum Driveshaft with NEW U-Joints
$100 have 3
NEW SS PBR Front & Rear Brake set up. New calipers, slotted & driled rotors with pads.. Can include front spindles.. Very nice upgrade flr LT1 93-97 cars as well as 82-92 third gens
Front's with spindles $150
Rears (I have 2 sets) $100 NO Backing Plates
Factory Posi 10bolt 3.23 traction control & abs torsion style posi with brand new calipers, pads & slotted drilled rotors...
$350 complete
Front struts with Eibach lowering springs
$50obo
Rear LCA's clean & painted with new hardware & poly bushings installed
Panhard rod also with poly & hardware both GM STYLE STOCK
$50 & your stock arms? Obo also have the Poly Torque Arm mount and stock arm
LCA relocation brackets Bolt On.. $50
1LE front sway bar with new moog poly endlinks, bushings & hardware
$40.. $75 with matching rear bar
GM Factory LS1 K-Member. Complete with engine mounts, ALL NEW POLY... NEW Rack & Pinion..
$100
SS Rear Spoiler Black OEM $300
SS Hood Black OEM. Has 2 very minor repairs done and will need a fresh coat of paint.. Previous owner painted himself.. Comes with new hood rods
$500
SS "SLP Only" Emblems, Fenders, and rear Berger emblems... Red outlined with black centers...$75
Fenders doors bumpers quarter panel's are all dent free, rust free and paint is bery nice.. Chassis itself is totally rust free.. Never seen snow and hardly seen rain. TTop car SLP SS LOADED.
Rebuilt Ohio Title
Mint Dash Pad. Ebony $150 98-02 Camaro
Mint Dash Pad. Third gen 82-92 Camaro
$250
Third Gen seats.. Cloth manual buckets with vinyl sides. All black, really comfortable and hold you almost like a racing seat... Need some help, 2 fronts and solid rear back with 2 bottoms. Complete.
$350
Front Wheel Spacers for 4th gen/ corvette style wheel BS to work with third gen front hubs.. Searched for weeks to find someone who was actually reputable enough to buold a set that would take any abuse.. Payed over $400 for the pair.
Billet Hubcentric custom built Aluminum 2.125" wheel spacers
$250
Call or text for other parts.. Make offers..
Spohn Chromoly Double Adj "On Car Adjustable) LCA's & Panhard Rod.
Black powder coat
Del-Sphere on both ends
$300
18" Dale Earnheart Jr special edition wheels.. With 275 Nitto 555's with 65% or better
$700 obo
18" C5 Deep Dish Replicas 18X9.5" & 18X10.5" like new. Have almost new Continental Extreme Contact "DW's" 85% or better
$1,200
TH350 *Needs Work* less than 3,500 miles on 800hp build. Alot of money invested. Manual Valve Body.. Alot of internal work... Previous owner claimed that it slips once hot.. I drove it and beat on it for 30min with no issues bit expect it to need work.
Comes with $600 9" Dynamic Converters Stall Converter, 3,600stall.. All hand welded fins.. Nitrous/Balloon Plates..
$375 takes the Trans AND Converter.. Thats hardly more than a th350 core. Came off a LS1 383.
NEW only broke in LS7 Clutch & Flywheel. 500 miles includes all ARP hardware
$500obo
Also have a 1985 SS Monte Carlo Rolling Chassis, Rust free
$1,500
NEW FRESH 408. This engine is owned by a friend of mine, he needs it gone unfortunately but this thing has an easy $20,000 invested... Its turn key Boost ready. If I had the cash id own it. Makes me sick seeing it forsale as cheap as it is
$6,500 turn key. Details on request, well over 6k in the shortblock..Built for alot of boost.. 1500hp plus ready
Near perfect WS6 Ram Air Hood. OEM RED. $1,500
More I cant think of at the moment
Please text or call with any needs or questions, text would be best and I can call you when I get it.. All offer's considered EXCEPT on the LS1 & 4L60, thos are FIRM
Trending Topics
#10
I do have an fbody pan.. $250 for the whole kit
Pan
Baffle
Tray
Pic up
Bolts
Newer gm gasket
Dipstick
Oil level sensor...
$250 or $275 shipped...
As for the 1le I cant say ...
I only have the front sway bar ajd cant be sure 100% that it is a 1le but that is what I was told...
I can measure it and send pictures tho
Pan
Baffle
Tray
Pic up
Bolts
Newer gm gasket
Dipstick
Oil level sensor...
$250 or $275 shipped...
As for the 1le I cant say ...
I only have the front sway bar ajd cant be sure 100% that it is a 1le but that is what I was told...
I can measure it and send pictures tho