WTB: Gauges, Fittings, MC Resevoir, Clamps, and a lot more!
03-28-2012, 07:55 AM
#1
TECH Regular
Thread Starter
iTrader: (11)
Join Date: Feb 2009
Posts: 489
Likes: 0
Received 0 Likes
on
0 Posts
WTB: Gauges, Fittings, MC Resevoir, Clamps, and a lot more! Need a *few* little things yet, but they really add up so if you have a used one or new one that's just sitting around let me know!
Autometer Ultra-Lite Gauges
-fuel level 0-90ohms 2 1/16
-voltmeter 2 1/16
-Electric Fuel pressure 0-100psi 2 1/16
-Electric Speedo 3 3/8
-Also need a Trans temp gauge, electric 2 1/16 Phantom series
Fittings and Hose
-Let me know what you have and are willing to get rid of, I need -6 through -12. Black fittings are preffered but other's will do!
-As for the Hose I need ~20' of -8, ~20' of -10, and ~10' of -12. These can be stainless or black braided.
Master Cylinder Resevoir
-A stock 3rd gen one would be perfect, but anything that can be mounted, sealed, and hold a cup or two of fluid would work.
Valve Cover Bolt
-From a center bolt gen3/4 valve cover, I only need one.
Lifter Trays
-NEW LS2 lifter trays. I know this may be a long shot but it's worth a shot!
Exhaust
-2.5" Clamps
-2.5" bullet mufflers x2
-2.5" X pipe
-2.5" exhaust pipes
-Hangers
Transmission
-Any t-56 slave shims
*Driveshaft Safety Loop for 3rd or 4th gen F-Body
*PST or Equivelent driveshaft, Stock length
*Rear End, 3rd gen width only, 4.11 gears or similar.
If you have any of the above post or PM me! Cash in hand or Paypal ready
Autometer Ultra-Lite Gauges
-fuel level 0-90ohms 2 1/16
-voltmeter 2 1/16
-Electric Fuel pressure 0-100psi 2 1/16
-Electric Speedo 3 3/8
-Also need a Trans temp gauge, electric 2 1/16 Phantom series
Fittings and Hose
-Let me know what you have and are willing to get rid of, I need -6 through -12. Black fittings are preffered but other's will do!
-As for the Hose I need ~20' of -8, ~20' of -10, and ~10' of -12. These can be stainless or black braided.
Master Cylinder Resevoir
-A stock 3rd gen one would be perfect, but anything that can be mounted, sealed, and hold a cup or two of fluid would work.
Valve Cover Bolt
-From a center bolt gen3/4 valve cover, I only need one.
Lifter Trays
-NEW LS2 lifter trays. I know this may be a long shot but it's worth a shot!
Exhaust
-2.5" Clamps
-2.5" bullet mufflers x2
-2.5" X pipe
-2.5" exhaust pipes
-Hangers
Transmission
-Any t-56 slave shims
*Driveshaft Safety Loop for 3rd or 4th gen F-Body
*PST or Equivelent driveshaft, Stock length
*Rear End, 3rd gen width only, 4.11 gears or similar.
If you have any of the above post or PM me! Cash in hand or Paypal ready
