LS1TECH - Camaro and Firebird Forum Discussion - Search Results

Notices
 
Search: Posts Made By: tblentrprz
Showing results 1 to 25 of 277
Search took 0.09 seconds.
06-13-2019, 11:39 AM
Replies: 274
Views: 41,771
Posted By tblentrprz

I hear ya on the noise pollution My poor...

I hear ya on the noise pollution My poor neighbors endured my teens while hearing my 70 Nova SBC at 8000rpms and open headers banging through the gears with 4.88s. Their poor ears and heart shock!
06-06-2019, 10:37 AM
Replies: 17
Views: 1,803
Posted By tblentrprz

With a BR7 and same timing, you'll likely see...

With a BR7 and same timing, you'll likely see timing mark move up the gnd strap into a safer range.
05-31-2019, 02:56 PM
Replies: 12
Views: 2,053
Posted By tblentrprz

Just some thoughts - without a $$ budget clearly...

Just some thoughts - without a $$ budget clearly identified, you are fooling yourself and anyone trying to help you.

Most would tell you, sell the LS1. It's worth a lot more in 1 piece running. ...
05-30-2019, 11:51 AM
Replies: 26
Views: 1,623
Posted By tblentrprz

^^^^ this? More than 1 thread, go 1 colder.

^^^^ this?

More than 1 thread, go 1 colder.
05-19-2019, 04:28 PM
Replies: 26
Views: 1,623
Posted By tblentrprz

The coldest plug that doesn't foul is the safest...

The coldest plug that doesn't foul is the safest to run.
05-03-2019, 01:04 PM
Replies: 31
Views: 2,074
Posted By tblentrprz

A simple mechanical vacuum/pressure gauge...

A simple mechanical vacuum/pressure gauge connected to oil dip stick tube might give you some insight.
04-30-2019, 04:22 PM
Replies: 5
Views: 541
Posted By tblentrprz

What IAT? Need to read all the plugs after 17psi...

What IAT? Need to read all the plugs after 17psi and pump gas pull to better understand whats going on. Also, how much timing adjustment around peak tq?
04-30-2019, 04:12 PM
Replies: 31
Views: 2,074
Posted By tblentrprz

What size vents on motor? Can you log crankcase...

What size vents on motor? Can you log crankcase pressure? Any concerns with turbo oversupply or drains? There is a benefit to have crankcase under vacuum. Keeping oil out of the combustion...
04-29-2019, 10:47 PM
Replies: 31
Views: 2,074
Posted By tblentrprz

Oil in charge pipe caused by PCV? How much...

Oil in charge pipe caused by PCV? How much crankcase pressure is required to push that much oil through rings or valve seals into the induction system? How big are your crankcase vents?
04-26-2019, 02:15 PM
Replies: 19
Views: 782
Posted By tblentrprz

Quick check to identify if fuel - spray brake...

Quick check to identify if fuel - spray brake cleaner (1-2 sec) into intake manifold and give her a crank. If it responds well, you need to chase fuel supply pressure or parameters.
04-16-2019, 07:53 PM
Replies: 22
Views: 1,399
Posted By tblentrprz

Side note - many Bosch style 30A/40A relay...

Side note - many Bosch style 30A/40A relay sockets often have 14ga or even 16ga power wires which obviously can't handle anywhere close to current required. Overheated relays and wire terminals...
04-14-2019, 05:36 PM
Replies: 1
Views: 319
Posted By tblentrprz

Let us know how it works. The tensioner...

Let us know how it works. The tensioner typically is on the slack side of crank pulley. i.e. not before it drives (pulls on) any load/accessory. Also, spring tension should be strong enough to...
03-27-2019, 09:04 PM
Replies: 30
Views: 2,104
Posted By tblentrprz

Remind us: motor ci comp ratio fuel cam...

Remind us:
motor ci
comp ratio
fuel
cam specs

50 - 100 shot likely get it going.
03-17-2019, 11:45 AM
03-08-2019, 08:16 PM
Replies: 196
Views: 23,846
Posted By tblentrprz

40F temp drop should be good for 80ish hp.

40F temp drop should be good for 80ish hp.
03-04-2019, 07:16 PM
Replies: 37
Views: 5,117
Posted By tblentrprz

Do you mind sharing CI, rpm and back pressure?

Do you mind sharing CI, rpm and back pressure?
02-06-2019, 09:17 PM
Replies: 86
Views: 9,413
Posted By tblentrprz

HOAs can be petty. Take great care of your...

HOAs can be petty. Take great care of your neighbors so they don't have anything to complain about (respect their desires, coordinate a block party - donation box covers cost, offer discounted...
01-27-2019, 09:38 PM
Replies: 63
Views: 15,414
Posted By tblentrprz

Motorcraft CM5187 for 5.0...

Motorcraft CM5187 for 5.0 https://www.rockauto.com/en/catalog/ford,2013,mustang,5.0l+v8,1503807,fuel+&+air,fuel+injector,6224...
01-22-2019, 09:36 PM
Replies: 9
Views: 564
Posted By tblentrprz

Side note - not all 4 primaries flow at the same...

Side note - not all 4 primaries flow at the same time. Collector could be reduced to 3.5 sq in. (~2.125") Amazing to see collectors that look abnormally small on high end headers.
01-12-2019, 06:42 PM
Replies: 28
Views: 1,670
Posted By tblentrprz

Please explain

Please explain
11-22-2018, 09:01 AM
Replies: 20
Views: 1,157
Posted By tblentrprz

In the interest of OP improvements/benefits (and...

In the interest of OP improvements/benefits (and not high jacking his thread), what was rpm limit before? Any idea on increase in whp or trap mph with increased rpm?
11-15-2018, 08:39 PM
Replies: 11
Views: 788
Posted By tblentrprz

Fuel limited, not volume but octane rating and...

Fuel limited, not volume but octane rating and knock suppression. How much whp with 91 have you made at what CI and IAT? How much water/meth did you spray?
11-14-2018, 09:34 AM
Replies: 11
Views: 788
Posted By tblentrprz

You'll be fuel limited to reach 1000whp without a...

You'll be fuel limited to reach 1000whp without a lot of meth and rpm. Detonation is the killer. 10:1 at upper limit for pump gas and streetable cam. Tuning window will be smaller. Better with...
11-05-2018, 08:39 PM
10-29-2018, 02:13 PM
Replies: 28
Views: 1,255
Posted By tblentrprz

Cam and turbo to go 7500 at 20psi and you'll gain...

Cam and turbo to go 7500 at 20psi and you'll gain 20 to 25% more hp than current setup (assuming fuel system is up to the task). Jose can spec the details for your current setup.
Showing results 1 to 25 of 277
 


 
Forum Jump

About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.