LS1TECH - Camaro and Firebird Forum Discussion - Search Results

Notices
Search: Posts Made By: markster
Showing results 1 to 14 of 14
Search took 0.48 seconds.
Forum: Marketplace
04-23-2019, 08:13 PM
Replies: 0
Views: 231
Posted By markster

EFI Source Gold Box Megasquirt 3

EFI Source Gold Box Megasquirt 3 - like new, lightly used Megasquirt 3
ECU. This ECU will run a LS engine with all features. See here for
features and info:
...
02-25-2019, 03:33 PM
Replies: 80
Views: 9,270
Posted By markster

Yes i believe freq-in = freq-out as well. I...

Yes i believe freq-in = freq-out as well. I don't have any way to measure it but I can definitely hear the fan buzz change as I change the frequency on my MS3.

I tested a 902-310 with f-body...
02-24-2019, 11:41 AM
Replies: 80
Views: 9,270
Posted By markster

I found the wiring instructions in the MS3PRO...

I found the wiring instructions in the MS3PRO manual. Search the manual for RY330K:

https://www.ampefi.com/wp-content/uploads/ms3pro_ultimate_manual.pdf
02-23-2019, 06:25 PM
Replies: 80
Views: 9,270
Posted By markster

Does anyone have a wiring diagram to properly...

Does anyone have a wiring diagram to properly connect the 902-310 or 902-303 to a MS box?

thanks!
02-17-2019, 11:37 AM
Replies: 80
Views: 9,270
Posted By markster

Does anyone know where to get the plugs for the...

Does anyone know where to get the plugs for the ebay Mitsubishi fan controller?

thanks
12-03-2018, 05:49 PM
Replies: 4
Views: 446
Posted By markster

Car looks good! The wiring harness that runs...

Car looks good!

The wiring harness that runs on the passenger side is for the engine control and can be removed. The wiring harness on the driver side mostly runs the car and should be retained....
11-28-2018, 08:25 PM
Replies: 21
Views: 2,748
Posted By markster

I have the EFI Source Gold Box. Works great, no...

I have the EFI Source Gold Box. Works great, no complaints. I like it so much I just bought a second one.
11-24-2018, 08:23 AM
Replies: 59
Views: 15,782
Posted By markster

Yes, i pulled the rack forward a few inches then...

Yes, i pulled the rack forward a few inches then installed the shaft thru the headers. I also had to replace the large rag joint with an ebay steering ujoint. I have a 4L80e and had to cut off the...
07-20-2018, 04:51 PM
Replies: 9
Views: 498
Posted By markster

What adapter fittings do you use for the GF652? ...

What adapter fittings do you use for the GF652?

Would these work?

https://www.jegs.com/i/JEGS/555/100705/10002/-1
09-26-2017, 06:10 AM
Replies: 59
Views: 15,782
Posted By markster

Im using the stock shaft but needed to weld on a...

Im using the stock shaft but needed to weld on a smaller ebay steering u-joint. The stock rag joint would not fit between the tubes.
01-27-2017, 06:46 PM
Replies: 53
Views: 8,233
Posted By markster

Do you have a picture of which way you mounted...

Do you have a picture of which way you mounted the aje mounts on the engine block?
01-08-2017, 02:09 PM
Replies: 53
Views: 8,233
Posted By markster

What headers are you using? Hows the clearance?

What headers are you using? Hows the clearance?
01-08-2017, 09:20 AM
Replies: 53
Views: 8,233
Posted By markster

What fuel filter did you use and how did you...

What fuel filter did you use and how did you regulate it and connect the lines to the truck fuel rails? Also it looks like you routed the lines up the passenger side is that correct? Thanks
01-08-2017, 07:51 AM
Replies: 53
Views: 8,233
Posted By markster

Very nice build! Where did you get the fuel hat...

Very nice build! Where did you get the fuel hat that has 6an hose fittings?
Showing results 1 to 14 of 14


 
Forum Jump

About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.