LS1TECH - Camaro and Firebird Forum Discussion - Search Results

Notices
 
Search: Posts Made By: kaharvey88
Showing results 1 to 25 of 170
Search took 0.12 seconds.
10-16-2017, 01:46 PM
Replies: 4
Views: 655
Posted By kaharvey88

Bump.

Bump.
10-11-2017, 02:52 PM
Replies: 4
Views: 655
Posted By kaharvey88

They have the chamfered lip. Hard to see in the...

They have the chamfered lip. Hard to see in the pic because of the soot on them. I can clean them up and get a better pic if you want.
10-10-2017, 08:47 PM
Replies: 4
Views: 655
Posted By kaharvey88

Corsa clone exhaust tips

Corsa clone tips. Used. 3" inlet dual 4" outlets. $80 shipped for the pair.
06-05-2017, 06:01 PM
Replies: 6
Views: 956
Posted By kaharvey88

Still don't want to ship?

Still don't want to ship?
04-24-2017, 02:14 PM
Replies: 15
Views: 1,335
Posted By kaharvey88

Still got it? I know someone looking for one

Still got it? I know someone looking for one
02-19-2016, 06:48 PM
Replies: 6
Views: 1,354
Posted By kaharvey88

Check your local Slo-Reilly's. I'm pretty sure I...

Check your local Slo-Reilly's. I'm pretty sure I bought a pack of the Dormans from their "Help!" section for a few bucks
01-01-2016, 07:50 AM
Replies: 1
Views: 371
Posted By kaharvey88

UMI Driveshaft Loop trade for LT1 tail lights

I have a new, never installed UMI Driveshaft Loop that I bought for my car and it wouldn't fit with my exhaust setup. Looking for a nice set of lt1 Camaro tail lights for trade. Will also sell out...
10-29-2015, 06:07 PM
Replies: 2
Views: 1,541
Posted By kaharvey88

Thanks for the response. The only cam I have...

Thanks for the response. The only cam I have access to at the moment is a 2000 camaro ls1 cam, but if I'd be better off with the 5.3 cam I'll just stick with it.
10-29-2015, 05:04 PM
Replies: 2
Views: 1,541
Posted By kaharvey88

5.3 cam in 5.7

I've got a 01 lm7 that has some rust in 2 cylinders so I figured I'd go ahead and bore it to a 5.7. This will be going in a 78 cj7. I'm not really concerned with power past 5000. This will be a...
10-28-2015, 11:40 PM
Replies: 6
Views: 4,920
Posted By kaharvey88

Correct, but I added a wire to pin 42 where there...

Correct, but I added a wire to pin 42 where there wasn't one before. Pin 42 is supposed to be fan one relay control from what I've read. I suggested a segment swap to my tuner and he said, "it would...
10-22-2015, 08:33 AM
Replies: 6
Views: 4,920
Posted By kaharvey88

I don't have a way to check anything, but I'm...

I don't have a way to check anything, but I'm using a reputable tuning service. He seems pretty sure that he knows what he's doing, but I can't help but think that it's in the tune. Is there anyone...
Forum: Parts Wanted
10-16-2015, 05:01 PM
Replies: 6
Views: 711
Posted By kaharvey88

I have one I'm about to pull off my car to...

I have one I'm about to pull off my car to replace it with a cowl hood. Has some damage on passenger side front and driver side rear corner (bought it that way). I'm located in southeast AR. I can...
10-16-2015, 02:26 PM
Replies: 6
Views: 4,920
Posted By kaharvey88

5.3 swap fan wiring problem

Here's what I got..... 01 2wd truck harness and pcm, 04 5.3 and 4l60e. It's swapped into a 1990 c1500 regular cab short bed 2wd. I got everything figured out by either info I found on here,...
Forum: Parts Wanted
10-13-2015, 06:52 PM
Replies: 1
Views: 378
Posted By kaharvey88

5.3 truck fuel injector connector

I need one for top secret experiment :secret2:
10-04-2015, 09:46 PM
Replies: 9
Views: 620
Posted By kaharvey88

PITA ----> Pain In The Ass..... Yea it's bad. I...

PITA ----> Pain In The Ass..... Yea it's bad. I suggest getting under the back of your car and look for a loose suspension component. Check lower control arms, torque arm bolts, shocks, anything that...
09-29-2015, 10:15 PM
Replies: 0
Views: 2,923
Posted By kaharvey88

Need help with cold air intake for 5.3 in 1990 c1500

Can someone tell me for sure if one of these will fit like the one in the attached pics? I'm running a very similiar setup as far as a/c compressor placement and such. I can't find the exact intake...
09-04-2015, 04:56 PM
Forum: Parts Wanted
08-06-2015, 07:07 PM
Replies: 0
Views: 214
Posted By kaharvey88

WTB "Smaller" aftermarket cam for 5.3

Looking for something similar to a 218 int 222 ex duration .560ish lift 113+ LSA. Split duration is not required, just preferred. Smaller than that is fine don't want much bigger than that though....
07-23-2015, 09:16 AM
Replies: 2
Views: 731
Posted By kaharvey88

Pics added

Pics added
07-22-2015, 09:53 PM
Replies: 8
Views: 1,199
Posted By kaharvey88

It's 6.5" end to end

It's 6.5" end to end
07-22-2015, 04:19 PM
Replies: 4
Views: 2,204
Posted By kaharvey88

Bump^

Bump^
07-22-2015, 04:19 PM
Replies: 10
Views: 789
Posted By kaharvey88

Bump^

Bump^
07-22-2015, 04:18 PM
Replies: 5
Views: 470
Posted By kaharvey88

Bump^

Bump^
07-22-2015, 04:17 PM
07-22-2015, 04:16 PM
Replies: 8
Views: 1,199
Posted By kaharvey88

Bump^

Bump^
Showing results 1 to 25 of 170
 


 
Forum Jump

About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.