When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Anyone have the special timing gear pulling tool? Jaw pullers aren't working.
I bought a small one from Autozone that worked pretty well. Had to slip a small 1/8"- 1/4" piece of steel between the screw and the crank but it worked. If you'd like I can send you the part number, or we could maybe work something out- I was going to return it but if people want to rent it maybe I'll hang on to it.
I bought a small one from Autozone that worked pretty well. Had to slip a small 1/8"- 1/4" piece of steel between the screw and the crank but it worked. If you'd like I can send you the part number, or we could maybe work something out- I was going to return it but if people want to rent it maybe I'll hang on to it.
I was looking for the Kent moore gear tool. Tried using the small gear puller with the thin Jaws, it just bends and pops off
I have a fender lip roller I'd be willing to lend out. Think I paid $75 for it. It's one of those tools you buy and only use once. Same rules apply.
$75 deposit + $10 rental and I'll ship without an upfront charge.
When item returns I'll refund the $75 - my out of pocket shipping cost.
I know the wheel will wear, I will not charge for a replacement wheel unless it's been totally neglected. You roll the fender gradually and don't force it and everything will be fine.
[QUOTE=I R Gunnr;19837135]I'll rent out my Sac City Corvette Alignit tools for the front and rear cover. I've used these many times and never had a leak.
Tool cost: 65
Shipping: Small flat rate ($7 maybe?)
Fee:$10[/QUOTE
Anyone have the special timing gear pulling tool? Jaw pullers aren't working.
I'm looking for a tool to remove the crankshaft sprocket from a 5.3 as well. Tried a 3 jaw from autozone and it was too thick. Bought a 2 jaw, and the fingers were too thin and slipped off.
$25 for a week plus shipping cost. $100 deposit for the tool which will be reimbursed when the tool is returned in good working condition. I will require two paypal transactions. One for $25 plus shipping and paypal fees (3%) and one for $100 deposit. The deposit will remain pending until the tool is returned functional. If the tool is not returned functional the deposit will be activated.
Will Deliver for extra fee depending on the location.
Will work on most vehicles
Quality constructed and will last for years
Padded jaws to protect painted surfaces Slotted holes will accommodate up to a 120.6 mm (4.75") 4 and 5 lug bolt circles.
Bolts directly to hub flange, and is held in place with the included dished washers and vehicles lug nuts.
Forming arm adjusts from 14" to 22 3/4".
Delrin & ball bearing forming roller is tough enough to form the fender without damaging the paint.
I live in Ontario Canada but travel on a regular/weekly basis to Port Huron MI (48060). I can ship from a local UPS store there with insurance and tracking. I will have to get a quote upon request.
Have a squeaky belt on your car that just wont go away? Need to properly align your supercharger belt for proper wear and belt life? See a lot of belt dust on your pulleys??
It is likely that one your accessory pulleys is misaligned causing premature belt wear which causes a loud whine and several decreases your belt life!! Here is the answer!!
I have a Gates 91006 belt alignment tool for rent. I personally used it to alignment my supercharger belt on my car and it worked amazing. There is a few videos online showing proper use of the tool!
It simply uses a strap to wrap around your crank pulley and then shoots a laser onto your other accessory drive pulleys showing any misalignment!
Don't go out and buy this tool to use it one time, just rent it and return it!
$25 for a week plus shipping cost. $100 deposit for the tool which will be reimbursed when the tool is returned in good working condition. I will require two paypal transactions. One for $25 plus shipping and paypal fees (3%) and one for $100 deposit. The deposit will remain pending until the tool is returned functional. If the tool is not returned functional the deposit will be activated.
I am located in Ontario Canada but travel to Port Huron MI 48060 on a weekly basis. I can ship this item from a UPS Store there. Shipping quotes available upon request and include tracking and insurance.
I need to rent a LSA/ZL1 blower dowel hole drilling jig. I believe Lingenfelter makes one, but I would rather not pay $175+ for a tool I will literally only use once.
Thanks guys!
im looking to rent on of these too. Were you ever able to find one for rent? I realize I could just remove the dowel pins instead but would be willing to drill the guide holes if I can rent the tool.
Goodson RRJ-350 Reluctor Ring Jig. Necessary tool for installing reluctor wheels on LS crankshafts
This ships from zip 53532.
Value (deposit): $160.00. Rental rate: $30.00 per week plus shipping to you.
As above guidelines, paypal payment of the deposit, plus the rental plus the shipping to you with insurance. You pay return shipping and the value is returned via paypal upon return and inspection.
PM me with your shipping address for rental quote.
01-20-2018, 09:12 AM
