wolfe racecraft anti roll bar on 02 fbody
#1
On The Tree
Thread Starter
iTrader: (1)
Join Date: Jan 2014
Location: new jersey
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
wolfe racecraft anti roll bar on 02 fbody
anybody on here have any experience with wolfe racecraft anti roll bar.. chassis shop is bout to install this on my moser fab 9 rear.. 20002 trans am. my issue is with ground clearence.. cant seem to find any pics dipicting how much ground clearence i will have with this bar..... thank you
Last edited by bnastystuntz; 09-27-2017 at 09:48 AM.
#3
On The Tree
Join Date: Jan 2016
Location: Indianapolis, Indiana
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
I think that type of sway bar is mounted above the rear end. Different from traditional "factory" sway bars. I don't think you can even see it from the rear when installed.
So.....your picture is probably pretty accurate to represent final application.
So.....your picture is probably pretty accurate to represent final application.
#4
On The Tree
Thread Starter
iTrader: (1)
Join Date: Jan 2014
Location: new jersey
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
i bought the version that mounts to the rear axle tubes not the one that goes between the frame rail. im keeping my stock tank. i have just heard that the style bar i have hangs verry low..
#6
I don't know theirs for sure but I couldn't imagine it hanging any lower than the rear end at all. If you look at ours for our fabricated housing it isn't even the lowest point of the rear end.
#7
On The Tree
Thread Starter
iTrader: (1)
Join Date: Jan 2014
Location: new jersey
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE=MidwestChassis2;19738625]I don't know theirs for sure but I couldn't imagine it hanging any lower than the rear end at all. If you look at ours for our fabricated housing it isn't even the lowest point of the rear end.
from what i understand from lookin at theres based on the crappy pics they have on there site the bar actually
sits basically under the 3rd member
but as u can see this wont work cuz my tq arm has mounting points just like urs does.
from this pic it just longs like the mounting brackets would hang really low if i were to roll it back a lil bit to clear the tq arm mount
this is a lil better pic but not a fab9 and it doesnt depict the car with the wheels on the ground. this also looks like the bar mounts more away from the 3rd member . so this is y im confused
from what i understand from lookin at theres based on the crappy pics they have on there site the bar actually
sits basically under the 3rd member
but as u can see this wont work cuz my tq arm has mounting points just like urs does.
from this pic it just longs like the mounting brackets would hang really low if i were to roll it back a lil bit to clear the tq arm mount
this is a lil better pic but not a fab9 and it doesnt depict the car with the wheels on the ground. this also looks like the bar mounts more away from the 3rd member . so this is y im confused
Trending Topics
#9
#10
bnastystuntz we have a bent style that will fit any rear end and will sit in the same location as our straight version. It takes some type of swaybar bracket on the housing to work though. We do offer a weld on style just like the ones we use with our fabricated housings but I have seen people use the muffler stock style clamps before. Not what we recommend but I have seen it done.
#11
On The Tree
Thread Starter
iTrader: (1)
Join Date: Jan 2014
Location: new jersey
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
just wanted to updage this post for anyone who was curious bout the wolfe racecraft ARB.. chassis guy had to modify it to fit with the moser fab9 rear.. it was rolled back to clear the tq arm. hand to make custom brackets for this setup to work....
Last edited by bnastystuntz; 12-21-2017 at 01:26 AM.