TURBO 96 Trans Am
#1
Teching In
Thread Starter
iTrader: (3)
Join Date: Oct 2006
Location: Shoals
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
TURBO 96 Trans Am
Year: 1996
Make: Pontiac
Model: Trans Am
Price: $8000
Mileage: 79000
Private or Dealer Listing: Private Listing
Location (State): IN
Color: Gray
Transmission: Manual
Drivetrain: Rear Wheel Drive
LS Engine?: Car has other engine
http://ltxtech.com/forums/showthread...o-Turbocharger.
Also selling my 83 Chevette. 300 dollars for the car, 17 inch wheels and falken tires, 2 blown motors and 2 good transmissions. One is an auto and one 4 speed manual.
Also selling an 06 YFZ 450. Yamaha blue. Built motor with new tires on the rear. Runs really good. 3900
#2
Teching In
Thread Starter
iTrader: (3)
Join Date: Oct 2006
Location: Shoals
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
Oh boy I know I'm going to forget a lot of specs but to start off I started it with factory injectors. I heard it idle and shut it down. It's not driveable. I will need to be trailered. Needs 80 lb/hr injectors, wastegate, and radiator hoses. I built an all forged and balanced 383 LT1. Scat crank, Eagle rods, Keith Black blower pistons, ARP main studs and ARP head studs. It's just a 2 bolt main block but since it's balanced it hasn't been a problem. Just switched over to factory heads. Beehive valve springs. 1.5 ratio gold roller rockers from crane cams. Comp custom grind cam .540/.537 lift just for turbos. Trust me it doesn't run well naturally aspirated. I ported the intake. It has a BBK 58mm throttle body. New chevrolet valve covers. Spec stage 3+ clutch. New slave cylinder on its way from Summit this week. Canton 6 1/2 quart road race pan. LT1 log manifold kit from lt1boost.net. Here are my pics on his website. http://www.lt1boost.net/log_manifold_kit
Factory rearend. Factory 6 speed with a brand new B&M shifter. Stood the radiator straight up. Welded in two new crossmembers in the front. Repainted the front end the factory arctic white. Smoothed the frame rails and filled in most of the holes. Hid most of the wiring. 4 inch thick intercooler from ebay. intercooler pipes are all made. APEXi AVCR boost controller. MSD 6 BTM ignition. MSD coil. ZEX lt1 dry nitrous kit. New electric fans. electric water pump. Low mount alternator. No powersteering, no power brakes, no abs, no A/C, no heater at the moment. All these parts can all be put back on. I have most of the parts that were taken off except for the heating and A/C components. New Strange manual brake master cylinder. The list goes on with countless receipts but thats most of the big stuff. I will throw in all of the trans am and lt1 parts I have and even a set of BFG drag radials mounted on a set of camaro wheels.
Factory rearend. Factory 6 speed with a brand new B&M shifter. Stood the radiator straight up. Welded in two new crossmembers in the front. Repainted the front end the factory arctic white. Smoothed the frame rails and filled in most of the holes. Hid most of the wiring. 4 inch thick intercooler from ebay. intercooler pipes are all made. APEXi AVCR boost controller. MSD 6 BTM ignition. MSD coil. ZEX lt1 dry nitrous kit. New electric fans. electric water pump. Low mount alternator. No powersteering, no power brakes, no abs, no A/C, no heater at the moment. All these parts can all be put back on. I have most of the parts that were taken off except for the heating and A/C components. New Strange manual brake master cylinder. The list goes on with countless receipts but thats most of the big stuff. I will throw in all of the trans am and lt1 parts I have and even a set of BFG drag radials mounted on a set of camaro wheels.
#6
trans am project?
If you go to racingjunk .com and look up ad# 1932747....You will find a vehicle that is completely turnkey and will run 9 seconds flat on motor and if your crazy enough add some nitrous and go faster!!! This needs nothing at all! If your looking to get 8k I have about that in the heads! Let me kno Yhanks korey, I know you have some money in your car as well I'm just saying I don't care it's a project and if your wanting to sell it might be easier on a turnkey veh.????? Thanks for your time..#(309) 620-1507 Pekin Illinois (right next to Peoria) I do have a video of truck running a 9.92 before the Brodix BB2's were added.
#7
Teching In
Thread Starter
iTrader: (3)
Join Date: Oct 2006
Location: Shoals
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
I'd love to have that truck but I'm looking to sell mine for the money. Gotta get out from under some of these bills. I have a kid on the way. If it wasn't for that than I'd definately be interested. But family first