they are waay to baller for me but i will give em a shot, got too good a deal on them.

anyone have any info they can give me on these? 2-3 piece etc.

also wondering how to care for these.. the friggen inside of the wheel is mirror polished!

check em out

http://www.fastrides.com/photos/mm/category1073.aspx

 

Haha, i've never seen anyone do the "look how big my lip is cell phone" picture on the INSIDE of the wheel, haha. Look nice, i like those wheels for sure!

 

I like em. They will look good.

 

cool man those are bad ***

 

the inside lip was just too blingin' not to, its a better finish than the outer lip of any wheel i've had

 

Were those the ones that were in the for sale section? They are defiantly badass! They remind me alot of my wheels..

 

yes, i got them from RDF over the weekend.

i had to get them with that price tag!

your car is the viper grey right? whats the paint code? i was thinking a lighter grey for the new car this go round.

thanks

 

Thought so, I seen those an wondered what that guy was smoking to sell a set of Iforged wheels for that price. You got a hell of a deal.!

No my car is GM SUV Pewter metalic, with silver pearliesant flake added.

Theres a guy on here with those wheels on a black WS6 and that thing looks amazing. I think you should leave it black..

 

its either going carbon metallic like the last one or a little lighter.. i would prefer not go as light as yours but i'm just shopping around.

 

Damn donations from LS1Tech members does wonders

 

when i had mine i polished them once a week.... and took them off the car and washed them in the tub.....

 

Oh you rat bastard!

I still got you beat by an inch though.

For what it's worth, polishing these sucks. It's easily one of the hardest designs to keep clean. Keeping the barrels clean on a DD car will be damn near impossible.

It just takes a lot of time and patience.

EDIT:

As per your question, those are a 2piece wheel. I've tried at least 10 different polishes, and I always come back to Mothers Billet.

The shine it yields has yet to be matched. It applies very easily as well. I've tried using the Mothers Powerball stuff, but IMO it's no good. On these wheels it doesn't do a good job on the insides of the spokes.

I use a air powered blue point polisher, with 3" pads. I use buffing pads, and cut each of them up. I get 3, 3" pads out of them.

Best way it can be done, itt just takes a lot of time. All it takes is a puddle or some rain to bring you back to square one.

Rob

 

no ls1tech member money was spent on these wheels

rob u dont gotta worry, my t/a is going back to my old raptor hood and grey paint

 

No big deal, had to happen sooner or later. It's the best looking design on the TAs IMO. Fikse FM/10, etc. 10 spokes rule.

I was just thinking to myself. I wonder what the weight difference is between the 18" 3 piece wheels I have. Vs. the 17" 2 piece design.

What sizes did those wheels come in? Mine are 18x9 up front, 18x10 out back.

If I remember right, the fronts were about 20 lbs, and the rears were about 1.5 lbs. more. Weigh those bitches when you get them!

 

my fronts are 17*8 and rears 17*10 (measured inside)

 

Thats 4 cell phones! Very nice set of wheels you have there, and your car has always been awesome!

 

nice choice, iFORGED bling ftw

 

Here's some teaser pics for you. What kind of tires are you going to run?

 

Those rims are BADASS!!!

 

oh im familiar with those pics all ready.

my center caps look different than those.. what kind of lug nuts are they too?