Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Electrical Guides
- Camaro and Firebird: How to Replace the Starter
Step by step instructions for do-it-yourself repairs
Browse all: Electrical Guides
How to replace starter
#1
How to replace starter
Hi
What specialty tools will I need to replace the starter on my 99 TA...
And is it a PITA? Any advice? I'm gonna be doing it in the parking lot at work, so I need to make sure I got everything!
Jack stands are a given.
Thanks!
As back ground, I'm doing this 'cause the car won't crank when I hit the key. The security light isn't flashing, and goes out after a few seconds, so I don't think its the VATS system. I'll be trying to replace the starter relay before trying to swap the starter, 'cause that fixed it last time i had this problem. I let the car sit over night, and it didn't try again in the morning. I also can hear the starter relay under the hood click, as well as the relay under the dash. \
Any other advice here?
What specialty tools will I need to replace the starter on my 99 TA...
And is it a PITA? Any advice? I'm gonna be doing it in the parking lot at work, so I need to make sure I got everything!
Jack stands are a given.
Thanks!
As back ground, I'm doing this 'cause the car won't crank when I hit the key. The security light isn't flashing, and goes out after a few seconds, so I don't think its the VATS system. I'll be trying to replace the starter relay before trying to swap the starter, 'cause that fixed it last time i had this problem. I let the car sit over night, and it didn't try again in the morning. I also can hear the starter relay under the hood click, as well as the relay under the dash. \
Any other advice here?
#2
12 Second Club
iTrader: (49)
a 13mm socket, and a 10mm wrench i beleive for the wires. the 13 is used for the mounting bolts, and the B+ wire, and the 10 is used for the S terminal. its been a while since ive changed mine, but i beleive this is the sizes. the starter change itself takes about 10-15 minutes.
#4
TECH Apprentice
iTrader: (5)
Join Date: Sep 2005
Location: Fort Myers, FL
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
If you are replacing the starter look at getting the truck starter as it has two equal length long mounting bolts. The stock LS1 starter uses one short, and one long bolt which can cause issues if the short side becomes loose, or breaks off, causing the long bolt to possible do some serious damage to the block. I was lucky when I shattered my flex plate that the starter broke, and my block wasn't broken. The price is the same, but read carefully if buying off ebay as sometimes the truck starter doesn't come with two long bolts, just reuse your long stock bolt.
Trending Topics
#8
TECH Apprentice
iTrader: (12)
Join Date: Oct 2005
Location: uptown dallas
Posts: 325
Likes: 0
Received 0 Likes
on
0 Posts
well to you sir above me. removing the wheels (since they bolt on to the vehicle) is easy, mainly because you dont need a tire machine to break the bead and dismount. getting the tires off of a rim isn't as easy as removing the starter. so my question to you is, are you serious? to op. remove the battery cables first, lift the vehicle to where you can fit under it, the two bolts that hold it in the block are 13mm, the two nuts that hold the signal wire and power wire are a 10mm and an 8mm. remove those and remove the wires. you can let the starter hang just dont let it drop down quickly. put the starter out of your way and replace/install in the reverse order. if you havent already done this then i hope this helps. lol
#9
Staging Lane
Join Date: Sep 2007
Location: Orlando, FL
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
to explain how easy it is, my started went out in a parking lot about an hour from my house but next to an o'reilly auto. walked over to oreilly, bought a starter, pushed my car over a recessed drain in the parking lot for a little extra room and changed it there in the parking lot lol.
#11
11 Second Club
Join Date: Oct 2004
Location: Camp Lejeune, NC
Posts: 332
Likes: 0
Received 0 Likes
on
0 Posts
oh WOW? (easy button)
well to you sir above me. removing the wheels (since they bolt on to the vehicle) is easy, mainly because you dont need a tire machine to break the bead and dismount. getting the tires off of a rim isn't as easy as removing the starter. so my question to you is, are you serious? to op. remove the battery cables first, lift the vehicle to where you can fit under it, the two bolts that hold it in the block are 13mm, the two nuts that hold the signal wire and power wire are a 10mm and an 8mm. remove those and remove the wires. you can let the starter hang just dont let it drop down quickly. put the starter out of your way and replace/install in the reverse order. if you havent already done this then i hope this helps. lol
#14
TECH Enthusiast
iTrader: (17)
Join Date: May 2004
Location: GA
Posts: 667
Likes: 0
Received 0 Likes
on
0 Posts
i actually just finished doing mine about 3 hours ago. it took me about an hour to do it, taking talk breaks with my wife. It wasn't hard at all, and honestly, i didn't even know where the starter was prior to installing let alone how to change it. but it was pretty dummy proof. I needed an extension for the 13mm bolts and had to remove a sensor from the tranny because my 1 7/8 long tubes would not let the starter come out easy. all in all, very easy job. about as easy as an oil change.
#15
I'm doing this right now on mine. My only issue is the oil pan sensor on the passenger side. It is directly under the starter and it will be so much easier to do this with that out of the way.
I can't figure out the clip! Has anyone else done this?
I can't figure out the clip! Has anyone else done this?
#20
On The Tree
iTrader: (1)
Join Date: May 2006
Location: a "ville"
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
Just thought I'd add,(since there was no mention of this and I had to wiggle my way back out from under the car to get them, grrr) you will also need a 15mm socket and extension to get the starter bolts out. I just did it. The 13mm and the 8 mm are for the wires. There is a dust shield too but don't take it loose.