Procharger pulley = ? boost
Thread Starter
TECH Enthusiast
Joined: Dec 2004
Posts: 588
Likes: 0
From: Zanesfield, OH
Procharger pulley = ? boost I know it is complicated to figure out but I would like to know how much boost you guys think this will make. I have Kooks long tubes 1 7/8", EPS cam 226/234 .598/.612 114LSA, stock heads, stock intake, and corsa catback.
Its a D1SC 8 rib, procharger spec'ed a 4.38" blower pulley. I requested to between 8-9psi range.
What do you guys think will I be close. Some delays in the dyno session it wont hit the rollers until Tuesday now. The tuner thinks it might be a bit large I guess we will find out for sure soon. Interested in your opinions.
Its a D1SC 8 rib, procharger spec'ed a 4.38" blower pulley. I requested to between 8-9psi range.
What do you guys think will I be close. Some delays in the dyno session it wont hit the rollers until Tuesday now. The tuner thinks it might be a bit large I guess we will find out for sure soon. Interested in your opinions.
Thread Starter
TECH Enthusiast
Joined: Dec 2004
Posts: 588
Likes: 0
From: Zanesfield, OH
That sucks, I hope procharger did their math right. I don't have a lot of time before the build needs completed. I plan on meeting some friends on power tour.
Anyone else have an opinion or experiance with a similar set up?
Anyone else have an opinion or experiance with a similar set up?
I know it is complicated to figure out but I would like to know how much boost you guys think this will make. I have Kooks long tubes 1 7/8", EPS cam 226/234 .598/.612 114LSA, stock heads, stock intake, and corsa catback.
Its a D1SC 8 rib, procharger spec'ed a 4.38" blower pulley. I requested to between 8-9psi range.
What do you guys think will I be close. Some delays in the dyno session it wont hit the rollers until Tuesday now. The tuner thinks it might be a bit large I guess we will find out for sure soon. Interested in your opinions.
Its a D1SC 8 rib, procharger spec'ed a 4.38" blower pulley. I requested to between 8-9psi range.
What do you guys think will I be close. Some delays in the dyno session it wont hit the rollers until Tuesday now. The tuner thinks it might be a bit large I guess we will find out for sure soon. Interested in your opinions.
Trending Topics
Thread Starter
TECH Enthusiast
Joined: Dec 2004
Posts: 588
Likes: 0
From: Zanesfield, OH
Well my pulley is larger so it will spin the head unit slower. Your pulley was the next size smaller compared to mine. I hope that gets it down to about 9psi, I dont want my stock engine to RIP to quickly. I am assuming yours didn't like the 13psi so well so it is now dead!
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Well my pulley is larger so it will spin the head unit slower. Your pulley was the next size smaller compared to mine. I hope that gets it down to about 9psi, I dont want my stock engine to RIP to quickly. I am assuming yours didn't like the 13psi so well so it is now dead!
If you are worried about it making too much boost, can you simply lower your rev limiter to say 6000rpm to keep the boost pressure down? Most of the procharged dyno's I've seen only rev to 6400-6500rpm where the NA heads/cam guys go to 7000 rpm.
