Emblempros.com September Sale
#61
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
Custom Grille emblem
Custom Onyx stainless lettering
Onyx custom emblem with carbon fiber.
Have not posted in a little bit.. so I though t I would put three parts up here.
#64
Teching In
Join Date: Mar 2015
Location: San Joaquin Valley, CA
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
Stop I can't afford all this.
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
#65
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
Stop I can't afford all this.
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Also, I have a set of 5th gen style Z28 badges that I bought in July of 2015. I recently ordered two more (one was damaged in a sideswipe). The side ones were flawless but the rear one started coming off of the base (I'm assuming it's because the rear of the car has a slight curve to it). Is there a way to make sure it doesn't happen again with the new badge?
Per my email instructions, you need to make sure the parts shape matches the curvature of the vehicle where you want to place it.
this is something that needs to be done by the customers, because we do not know where parts will be placed, and even on the back of this car the curvature changes the farther fro m the center you go.
So once you select a location, a very slight adjustment by hand might be needed prior to adhesion.
#67
TECH Veteran
iTrader: (14)
I might get some flak for this but I've kind of always wanted a custom RPO sheet in stainless. I'd have to come up with some of the RPO's though as I'd like it to apply to the cars current state rather than its v6 auto w68 call out. Car is practically a 1of1 at this point
Last edited by blackbyrd; 04-16-2017 at 09:49 PM.
#69
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
I might get some flak for this but I've kind of always wanted a custom RPO sheet in stainless. I'd have to come up with some of the RPO's though as I'd like it to apply to the cars current state rather than its v6 auto w68 call out. Car is practically a 1of1 at this point
Should not be any problem doing it.
Thanks, Roger
#77
FormerVendor
Thread Starter
iTrader: (32)
Join Date: Jul 2003
Location: Lexington, KY
Posts: 3,654
Likes: 0
Received 0 Likes
on
0 Posts
There should be no issues removing your stock parts. What is behind them is just clearcoat and paint. The fishing line trick works nice and fast.
Please let me know
#80
Hi, my wife has an 05 S197 Mustang GT with a roush supercharger, looking for ideas for supercharged emblems, what could you do for me please and also colour options, thanks colin.