Need Help With Badges!!!
#1
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
Need Help With Badges!!!
Ok so about 2 months ago i bought stainless ss badges from muffinbuster and im dying to put them on..but im getting a full paint job in about 2+ months. Can i put them on and then when the shop takes them off to paint the car can they use the same ones or am i gonna have to pay 70 bucks to get another set.
#4
12 Second Club
iTrader: (5)
Join Date: Aug 2002
Location: Middleville, Michigan
Posts: 1,789
Likes: 0
Received 0 Likes
on
0 Posts
If it's die cut tape I'd just wait. I'll make it look cleaner then if you try and reapply it and cut it out yourself. Unless you can get Muffinbuster to just sell you a set of pre cut tape.
#5
TECH Fanatic
iTrader: (15)
Join Date: Dec 2005
Location: _Nor caL_ (Bay areA)
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
i had to get my front end painted.. and they removed them, and put them back on no problem.. just make sure u tell them to put them in the exact spot them were.. like i think its 2 fingers across from the inside, and two fingers up..
Last edited by stangkiller2005; 04-18-2007 at 10:16 PM.
#7
TECH Fanatic
iTrader: (15)
Join Date: Dec 2005
Location: _Nor caL_ (Bay areA)
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mycamaroSS
already sweet. Thanks guys i guess im just gonna put them on tomorrow and do what you said stangkiller.
o, and if there painting ur car, id have them leave off the side trim while there at it LOOKS MUCH CLEANER IMO
Trending Topics
#8
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
yea that's what im doing im just gonna have them rip off the molding than paint it and also have them fill in the holes of the grille
also what's the best way to take the badges off (hair dryer)
also what's the best way to take the badges off (hair dryer)
#9
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
yea that's what im doing im just gonna have them rip off the molding than paint it and also have them fill in the holes of the grille
also what's the best way to take the badges off (hair dryer)
also what's the best way to take the badges off (hair dryer)
#10
TECH Fanatic
iTrader: (15)
Join Date: Dec 2005
Location: _Nor caL_ (Bay areA)
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mycamaroSS
yea that's what im doing im just gonna have them rip off the molding than paint it and also have them fill in the holes of the grille
also what's the best way to take the badges off (hair dryer)
also what's the best way to take the badges off (hair dryer)
do you have a pic of what your talkin bout on filling wholes on the grill?
#11
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by stangkiller2005
i used hair dryer, and an old credit card.. i hear fishing line is good to.
do you have a pic of what your talkin bout on filling wholes on the grill?
do you have a pic of what your talkin bout on filling wholes on the grill?
see where the holes are on the grille
#17
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
haha i wish dude...i did the whistler mods on those like a week ago and than i ended up replacing them(stil in the shop getting everything else fixed) now im gonna have to do it again ive taken apart my lights two times already and im getting tired of it. This better be the last time and if they end up fogging up this time im gonna go ape ****
#18
TECH Fanatic
iTrader: (15)
Join Date: Dec 2005
Location: _Nor caL_ (Bay areA)
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mycamaroSS
haha i wish dude...i did the whistler mods on those like a week ago and than i ended up replacing them(stil in the shop getting everything else fixed) now im gonna have to do it again ive taken apart my lights two times already and im getting tired of it. This better be the last time and if they end up fogging up this time im gonna go ape ****
#19
TECH Veteran
Thread Starter
iTrader: (4)
Join Date: Aug 2006
Location: San Marcos/Plano, Texas
Posts: 4,821
Likes: 0
Received 0 Likes
on
0 Posts
^ yea it better not be too hard or ill **** my pants......haha yea i really want an slp grille too but i really dont feel like putting down 270 for a grille.
#20
TECH Fanatic
iTrader: (15)
Join Date: Dec 2005
Location: _Nor caL_ (Bay areA)
Posts: 1,588
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mycamaroSS
^ yea it better not be too hard or ill **** my pants......haha yea i really want an slp grille too but i really dont feel like putting down 270 for a grille.