Right cam for setup CC 54-000-11 specs inside
#1
TECH Enthusiast
Thread Starter
iTrader: (12)
Join Date: Aug 2006
Location: Texas
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
Right cam for setup CC 54-000-11 specs inside
OK heres whats on the chopping block. A 6.2l shortblock, PRC stage 2 heads, headers, exhaust... etc through an automatic. But I am a little iffy on the cam. It seems a little small to me. Specs are as follows.
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?
#3
Old School Heavy
iTrader: (16)
OK heres whats on the chopping block. A 6.2l shortblock, PRC stage 2 heads, headers, exhaust... etc through an automatic. But I am a little iffy on the cam. It seems a little small to me. Specs are as follows.
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?
#5
TECH Enthusiast
Thread Starter
iTrader: (12)
Join Date: Aug 2006
Location: Texas
Posts: 533
Likes: 0
Received 0 Likes
on
0 Posts
My bad I do not know why I put automatic. This is a 6 speed built m6 with a stage 3 monster clutch, 3.73 gears,6.2l short-block, PRC stg 2 heads, headers, exhaust. I intend to go as fast as possible with a bigger cam that would accommodate my setup better. I think this cam I have is to small..
#6
Old School Heavy
iTrader: (16)
My bad I do not know why I put automatic. This is a 6 speed built m6 with a stage 3 monster clutch, 3.73 gears,6.2l short-block, PRC stg 2 heads, headers, exhaust. I intend to go as fast as possible with a bigger cam that would accommodate my setup better. I think this cam I have is to small..
#7
11 Second Club
iTrader: (33)
Join Date: Aug 2004
Location: Gloucester, VA
Posts: 819
Likes: 0
Received 0 Likes
on
0 Posts
OK heres whats on the chopping block. A 6.2l shortblock, PRC stage 2 heads, headers, exhaust... etc through an automatic. But I am a little iffy on the cam. It seems a little small to me. Specs are as follows.
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?
ls1 3721R/3719R HR113+3
CAM SPECS--- INT. EXH
ADV DUR: 271 285
DUR @ 50: 222 232
VALVE LIFT: .580 .280
LSA: 113.0
Go big or go home?