LS6 heads and 231/231
#1
Staging Lane
Thread Starter
Join Date: Jan 2004
Location: central OK
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
LS6 heads and 231/231
a buddy of mine is cutting me a SWEET deal on NIB tsp 231/231 .598/.598 112. i'm planning on putting a set of 243's on there at the same time. i just stumbled on the Christmas special that patriot perf. is having and their brand new 243's for $350 look too good to pass up!!!
my question is... should i have the heads milled for a slight bump in compression? or should i just go the thinner gasket route? or both? or neither? i'm totally up in the air on what the ideal setup would be with this cam. am i looking at any PTV issues by doing any/all of this? i've been trying to pay attention to all the DCR -SCR talk on here but i am by no means versed in any of it! what do you all think would be my best route to a hard running stoplight/ highway pounder?
i'm gonna call Patriot tomorrow and see what they tell me, but i'd really like to hear what some of you have to say...
thanks
mac
my question is... should i have the heads milled for a slight bump in compression? or should i just go the thinner gasket route? or both? or neither? i'm totally up in the air on what the ideal setup would be with this cam. am i looking at any PTV issues by doing any/all of this? i've been trying to pay attention to all the DCR -SCR talk on here but i am by no means versed in any of it! what do you all think would be my best route to a hard running stoplight/ highway pounder?
i'm gonna call Patriot tomorrow and see what they tell me, but i'd really like to hear what some of you have to say...
thanks
mac
#4
TECH Fanatic
iTrader: (3)
Join Date: Apr 2006
Location: Texas
Posts: 1,284
Likes: 0
Received 0 Likes
on
0 Posts
Id run thinner headgaskets .040 and standard 64cc . the thinner gasket will be = to a .015 cut off the heads .
68.5 IVC @.006 11.0:1 SCR / 8.5:1 DCR {this is if the cam is +4 advance installed 108 ICL }
70.5 IVC @.006 11.0:1 SCR / 8.4:1 DCR +2 advance 110 ICL
68.5 IVC @.006 11.0:1 SCR / 8.5:1 DCR {this is if the cam is +4 advance installed 108 ICL }
70.5 IVC @.006 11.0:1 SCR / 8.4:1 DCR +2 advance 110 ICL
#5
Staging Lane
Thread Starter
Join Date: Jan 2004
Location: central OK
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by cws T/A
Id run thinner headgaskets .040 and standard 64cc . the thinner gasket will be = to a .015 cut off the heads .
68.5 IVC @.006 11.0:1 SCR / 8.5:1 DCR {this is if the cam is +4 advance installed 108 ICL }
70.5 IVC @.006 11.0:1 SCR / 8.4:1 DCR +2 advance 110 ICL
68.5 IVC @.006 11.0:1 SCR / 8.5:1 DCR {this is if the cam is +4 advance installed 108 ICL }
70.5 IVC @.006 11.0:1 SCR / 8.4:1 DCR +2 advance 110 ICL
mac
#7
Staging Lane
Thread Starter
Join Date: Jan 2004
Location: central OK
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Gunnar@Patriot
If you have anymore questions Chris, please let us know. Thanks for the order.
i think that you've answered all that i was needing to know!!!
thanks again