ls1owner4life

iTrader: (17)

Hello, I have a 345HP CME SLP performance package. I want to buy a factory rating dash plaque but I do not know how much torque would accompany this package. Thank you

Tainted

iTrader: (9)

355ish,

I hope you know a bone stock, non special edition ls1 normally spits out 345hp in stock trim, the slp options added even more. why dont you get a dyno done and put the real specs on it?

'Trust'

iTrader: (24)

The SLP options BARELY added more. The lid and the freer flowing exhaust added maybe 10 RWHP. Tainted is on target with your torque, stock rating would be 355-360ish

Tainted

iTrader: (9)

your damn right tained is on target

Tainted does his best to help everyone out, and can *normally* put out correct info

02silvaZ

iTrader: (12)

wow, 'tainted' is stuck on himself a bit

i agree with gettin it dyno and then post those numbers

Tainted

iTrader: (9)

not really, just messin with trust some.

ls1owner4life

iTrader: (17)

I have no idea where to get a dyno done in Northern Cali and how much it would cost yet. 345HP and 355TQ would be a good guess?

'Trust'

iTrader: (24)

Does Tainted always refer to himself in the third-person? 'Trust' does! Lol. I'm funny. Anyway, yea 345 HP 355 TQ would be a good stock rating. I keep wanting to get something similar but I keep adding stuff!

Tainted

iTrader: (9)

lmao I got the same problem 'trust' One of these days ill quit with hp mods and start with suspension and get a little plaque

LT1wannabe

iTrader: (2)

Post something up in another forum and find out. It's Cali...somebody has a shop with a dyno there. I also think that's the best option. Or if you just don't want to pay, go with the 355 and call it a day.

SmokeySS

iTrader: (7)

That kinda sucks because I have the same package and adding longtubes and a ported TB my Camaro put down 368ft-lbs. Wahhh. I had that work done at Synergy in Fremont but there are other shops around - I've just never been to them.

MannyZ28

iTrader: (1)

Go to Dynojets website....they have a list there of all the shops that have their dyno.

http://www.dynojet.com/dyno_centers/...ive/index.aspx

Why guess if you can have they dyno sheet to prove it? If all else fails, print mine out...

ls1owner4life

iTrader: (17)

I know someone here must have gone to a dyno with the stock 345 package...

MannyZ28

iTrader: (1)

Are you really gonna keep the car the way it is? No more mods at all? Say it ain't so!

ls1owner4life

iTrader: (17)

haha don’t worry I am going to mod it but I want the plaque to match the factory ratings and look somewhat stock from a show/collectors/buyers point of view now and down the road. I only have 10K miles on it right now.

6LITEREATER

iTrader: (56)

Dyno runs are pretty cheap... Anywhere from $40 to $100. Defintely worth being accurate !

J. Brown

I factory ordered my SS with the 345HP package. On a dyno jet when the car was young 10-15K km's it dynoed @ the numbers listed below. (RWHP)

Cahill93Z28

i believe the poster was wanting to use factory ratings, hence him metioning he had the 345 package.

advice to poster, juts google the factory specs. that's what i did for my car when i got a plaque

J. Brown

Cahill93Z28 See above.

ls1owner4life

iTrader: (17)

I searched Google and could not find factory torque rating. I see your dyno numbers in your sig. The 345HP SLP package I THINK is rated at the motor. Therefore, I would need to know torque at the motor instead of wheels.

Cliff note:
I want an accurate (Not 350 to 360ish) depiction of the factory SLP ratings for an appearance mod without having to spend $50+ for a dyno in addition to the $40 plaque.