Few pics of a friends car I finished....
09-14-2009, 12:53 PM
#1
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Oct 2002
Location: Houston / Pearland
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Few pics of a friends car I finished.... I have been messing around with cars in my spare time by taking care of several old customers from MTI so I thought I would put up a couple pics. This one is a '07 C6 on which I installed heads, custom cam, FAST intake, clutch, built the rear end, and a small shot of gas. I welded a short section of aluminum pipe to the TB then drilled and tapped it in order support the nozzle which keeps the hard lines from flexing, this could eventually cause them to fail if allowed.
Here is another, I didn't get any pics after it was cleaned up and finished but you get the idea. It is a '07 Z that got kooks headers, cam, xcelerator intake, FAST LS7 manifold, NX kit and a set of 360 Forged 20's. One thing I though was pretty cool, although not my cup of tea, was making the silver six speed diagram on top of the shifter into the push button for the nitrous per his request. Looking it appears just as though the one pictured above does, yet you just push it with your thumb to activate the kit. (along with a switch, WOT switch, and window switch of course)
Here is another, I didn't get any pics after it was cleaned up and finished but you get the idea. It is a '07 Z that got kooks headers, cam, xcelerator intake, FAST LS7 manifold, NX kit and a set of 360 Forged 20's. One thing I though was pretty cool, although not my cup of tea, was making the silver six speed diagram on top of the shifter into the push button for the nitrous per his request. Looking it appears just as though the one pictured above does, yet you just push it with your thumb to activate the kit. (along with a switch, WOT switch, and window switch of course)
09-14-2009, 01:22 PM
#5
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Oct 2002
Location: Houston / Pearland
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
(not me) 
09-14-2009, 03:31 PM
#7
nice setup. was too busy checking out that black c5 z06 last time i stopped over there. didnt even see what was under the hood of the silver car. you should stop by my shop and check out the 750 hp 1900lb car were building up.
Trending Topics
. 
09-15-2009, 02:25 AM
#12
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Oct 2002
Location: Houston / Pearland
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
The one shown looks just like the one in the black car, which was made into a push button. He had wanted something like the LG "manswitch" and I thought that was kinda gay, mainly because of the name, so I made the silver piece into the pushbutton.
09-15-2009, 02:32 AM
#13
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Oct 2002
Location: Houston / Pearland
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, I hard lined the black car also but gave it to him with the braided lines installed because I didn't want the liability of having the hard lines break due to the constant flexing cause by the fixed MAF housing and rocking motor. I would have liked to relocate the MAP sensor to a less visible place also...
lolz
09-17-2009, 10:52 PM
#19
TECH Regular
iTrader: (9)
Join Date: Oct 2005
Location: Sugar Land
Posts: 488
Likes: 0
Received 0 Likes
on
0 Posts
Thanks, I hard lined the black car also but gave it to him with the braided lines installed because I didn't want the liability of having the hard lines break due to the constant flexing cause by the fixed MAF housing and rocking motor. I would have liked to relocate the MAP sensor to a less visible place also...
What about pics of Strawberry?????
09-17-2009, 11:08 PM
#20
TECH Enthusiast
Thread Starter
iTrader: (1)
Join Date: Oct 2002
Location: Houston / Pearland
Posts: 678
Likes: 0
Received 0 Likes
on
0 Posts
Unfortunately I am unaware of its existance. lol I will have to get some pics when I get home. I had to run out on a job for a week or two to deconstruct a platform here in the gulf. As soon as I get hime though I will be putting some finishing touches on the drivability tuning since putting on the intake I ported.