[no offense intended] 
berger panel
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Feb 2004
Posts: 1,112
Likes: 1
From: rosemount,mn/windsor locks,ct
berger panel anyone out there with a hugger orange camaro and a berger panel could you post up some pics for me i would greatly appreciate it. TIA
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Feb 2004
Posts: 1,112
Likes: 1
From: rosemount,mn/windsor locks,ct
Trending Topics
i just painted mine the flat black and around the bottom of all the letters it is already starting to chip and i havenvt had the panel on my car for more then two weeks... Any suggestions?
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Feb 2004
Posts: 1,112
Likes: 1
From: rosemount,mn/windsor locks,ct
that is why i am going with gloss black, gotta have the clear coat for protection.
I then had my buddy cut me a set of stickers to lay in over the CAMARO letters so the orange would be a perfect match.
Brought the panel over to my buddys body shop and shot the panel with base clear.
I think the end result was pretty good
Thread Starter
TECH Fanatic
iTrader: (2)
Joined: Feb 2004
Posts: 1,112
Likes: 1
From: rosemount,mn/windsor locks,ct
I removed the panel from the car and shot the entire panel.
I then had my buddy cut me a set of stickers to lay in over the CAMARO letters so the orange would be a perfect match.
Brought the panel over to my buddys body shop and shot the panel with base clear.
I think the end result was pretty good
I then had my buddy cut me a set of stickers to lay in over the CAMARO letters so the orange would be a perfect match.
Brought the panel over to my buddys body shop and shot the panel with base clear.
I think the end result was pretty good
definately looks good bro
what was involved in removing the panel? just have to take out the tailights and trunk liner? 
This picture in the link below is where I got on how to do my Manta stripe. I really like this car and it use to be Nineball's car, and I've debated on whether to add the Berger panel on my car in gloss black or not.
http://www.fquick.com/garages/viewga...viewimg&id=789
And here is a couple pics of my car.
http://www.fquick.com/garages/viewga...viewimg&id=789
And here is a couple pics of my car.
gloss does not look good...it looks like a replacement part out of a junk yard and that you haven't had a chance to paint it to match.
Its all personal preference, I cleared mine because my manta and sail panel are both gloss black and I wanted it all to match.
and your car looks VERY nice...
Obviously that isn't always the case, it's just the impression that I get on a lot of cars and it's why I went with a shaved and glossy black berger.