Painted front plastic piece in engine bay
if i remember correctly, i just took a small screwdriver under the small part of the pushpin, the middle part comes up and they just pop out.. or something like that (it was a while ago). either way, they sell them at autozone, so you wont hurt anything by cutting them.
Originally Posted by Fad2blk_98
This is kind of a bad angle, but this is what I did with rattle can. It turned out pretty good and is glossy, but just not like I wanted it. I think it look real good when done .. hopefully lol
I did this to my car as well. I took it out and used gloss black spray paint with a few coats of clear. That piece looks like crap if its not painted. This was the best picture I could find.
Thread Starter
TECH Resident
Joined: Nov 2003
Posts: 792
Likes: 0
From: Kansas
Originally Posted by kyles2000z
that looks real nice...better than other rattlecan jobs ive seen. if you're wanting the finish to be of the same quality as the exterior paint, you gotta go with a gun. either way, thats real nice.
Guest
Posts: n/a
Originally Posted by 67SS&99Z28
I did this to my car as well. I took it out and used gloss black spray paint with a few coats of clear. That piece looks like crap if its not painted. This was the best picture I could find.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Originally Posted by firefighter34
Hey guys stupid question here; Do you just rough up the plastic (interior painting) and use regular paint in a gun?
i did i write up here http://www.cardomain.com/ride/1514584/3 .
check that out to keep this thread on topic.
Thread Starter
TECH Resident
Joined: Nov 2003
Posts: 792
Likes: 0
From: Kansas
Originally Posted by kyles2000z
its alot more than roughing it up. most of my time was spent in paint prep, and my whole interior project took around 10-12 hours.
i did i write up here http://www.cardomain.com/ride/1514584/3 .
check that out to keep this thread on topic.
i did i write up here http://www.cardomain.com/ride/1514584/3 .
check that out to keep this thread on topic.
If i'm not mistaken, those are just the basic red fuel rail covers with a camaro ss plaque on there. I'm not sure where that decal came from, maybe he can chime in here, but it looks to me that they just have a decal over where it normally says Corvette. Also, parbreak does an awesome job with frc's if your wanting a custom set made.
Originally Posted by Justin01SS
67SS&99Z28,
That engine bay is sick! I want your covers! How did you make those??
That engine bay is sick! I want your covers! How did you make those??
Yes, they are Z06 FRC's. I had a Teri, member on here, make the emblems for me, but I do not think that she is making them anymore. You could ask her. Her screen name is Teri9672 i think.
Originally Posted by Unstang
Here is mine, I did it semigloss to match the brackets as close as I could...
