04' Mustang build...
Holy batman! Can't believe I hadn't ran into this thread yet. I bet you're excited to get it running. Nice cage too. Can you post pics of the side top bars going to the front. The ones parallel to the pillars
thanks
*Subscribing*
thanks
*Subscribing*
Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
Look in my sig. That's the link to my build from the chassis shop. If you need more pics, I'm sure Jake or myself can take a few of what you need to see!!
Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
the windows are tinted, so once up, you can't really see the cage. As far as the exhaust, it won't burn up the paint. Might stain it a little though LOL
Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
Not much new right now. It's getting all wired up and ready for Roger with C&S to come tune on it in a couple weeks.
I added a remote tranny cooler under the car, got the puke tanks installed under the front left fender for oil and water. Got the new rear end girdle on, got the front suspension set to where we want for now. Got it aligned and ready to go once the wiring is done.
I'll have video and updates once we get it fired up and ready to dyno in a couple weeks!!
I added a remote tranny cooler under the car, got the puke tanks installed under the front left fender for oil and water. Got the new rear end girdle on, got the front suspension set to where we want for now. Got it aligned and ready to go once the wiring is done.
I'll have video and updates once we get it fired up and ready to dyno in a couple weeks!!
so how'd it run?
and do you have any pics of the cage tubes at the front before the dash went in?
i checked out the pics in the shop's *****, but the only ones shown are with the bars not up in place and then with the dash installed...
i just wanna get a feel for how they were braced and routed behind the dash
thanks
and do you have any pics of the cage tubes at the front before the dash went in?
i checked out the pics in the shop's *****, but the only ones shown are with the bars not up in place and then with the dash installed...
i just wanna get a feel for how they were braced and routed behind the dash
thanks
Thread Starter
Teching In
Joined: Sep 2008
Posts: 32
Likes: 0
so how'd it run?
and do you have any pics of the cage tubes at the front before the dash went in?
i checked out the pics in the shop's *****, but the only ones shown are with the bars not up in place and then with the dash installed...
i just wanna get a feel for how they were braced and routed behind the dash
thanks
and do you have any pics of the cage tubes at the front before the dash went in?
i checked out the pics in the shop's *****, but the only ones shown are with the bars not up in place and then with the dash installed...
i just wanna get a feel for how they were braced and routed behind the dash
thanks
As far as the front dash bar. I took out the heater and all that so it was simple to do for Jake. It would have sucked, and as much of a genius as he is, it would have been a pain in the *** to do with it still there. I don't think the dash had to be notched at all to fit back in either. We have the 7531 box mounted to the bar up under it.
