Conversions & Swaps LSX Engines in Non-LSX Vehicles
Sponsored by:
Sponsored by:

Low idle and stalling issue

Thread Tools
 
Search this Thread
 
Old 10-04-2012 | 12:13 PM
  #1  
rick121's Avatar
Thread Starter
Teching In
iTrader: (4)
 
Joined: Mar 2010
Posts: 22
Likes: 0
Default Low idle and stalling issue

The car: 98 camaro v6 to LS1 swap

Up til now I have been having trouble getting the car started under her own power without jumpering relays, etc. Finally worked it out that she starts and stops when I tell her to but now she won't seem to charge via alternator and idles well below 1k. when I hit the throttle she dies instantly. Until now I was able to take her all the way to WOT with no hiccup. I have 40psi on the regulator and on the fuel rail via mechanical gauges. Oil pressure is good. Just replaced the TPS, IAC, MAF and almost every other sensor just to start off fresh. The really weird part is that even though she'll still die when I disconnect the MAF, the idle clears up a lot. defective?

any advice appreciated. Seriously. This swap should not be this hard...
Old 10-04-2012 | 12:25 PM
  #2  
psiconversion's Avatar
LS1Tech Sponsor
15 Year Member
iTrader: (5)
 
Joined: Feb 2007
Posts: 1,310
Likes: 11
From: Brick, NJ
Default

Fuel pressure should be somewhere around 58psi. 40 is too low. Could easily be your problem.

Jon
PSI
__________________

Your Source for LSX Conversion Parts!
www.psiconversion.com

Ebay Store
Facebook/psiconversion
Instagram/psiconversion

'Dont Let EFI Pass You By!'
Old 10-04-2012 | 02:12 PM
  #3  
rick121's Avatar
Thread Starter
Teching In
iTrader: (4)
 
Joined: Mar 2010
Posts: 22
Likes: 0
Default

Originally Posted by psiconversion
Fuel pressure should be somewhere around 58psi. 40 is too low. Could easily be your problem.

Jon
PSI
Everywhere I read said about 40... whats interesting is that it ran it before around 45. I will bump it up and try it. thanks!
Old 10-04-2012 | 04:22 PM
  #4  
psiconversion's Avatar
LS1Tech Sponsor
15 Year Member
iTrader: (5)
 
Joined: Feb 2007
Posts: 1,310
Likes: 11
From: Brick, NJ
Default

LS fuel pressure needs to be around 58. 40 is more typical of an LT1.

Jon
PSI
__________________

Your Source for LSX Conversion Parts!
www.psiconversion.com

Ebay Store
Facebook/psiconversion
Instagram/psiconversion

'Dont Let EFI Pass You By!'
Old 10-04-2012 | 07:25 PM
  #5  
rick121's Avatar
Thread Starter
Teching In
iTrader: (4)
 
Joined: Mar 2010
Posts: 22
Likes: 0
Default

Definitely squared away the acceleration! thank you so much! Turned out I also have a bad alternator and possibly MAF... replaced all three and it idles and accelerates, still no comm to the trans tho...
Old 10-05-2012 | 07:48 AM
  #6  
psiconversion's Avatar
LS1Tech Sponsor
15 Year Member
iTrader: (5)
 
Joined: Feb 2007
Posts: 1,310
Likes: 11
From: Brick, NJ
Default

What year is the engine/transmission?

Jon
PSI
__________________

Your Source for LSX Conversion Parts!
www.psiconversion.com

Ebay Store
Facebook/psiconversion
Instagram/psiconversion

'Dont Let EFI Pass You By!'



Quick Reply: Low idle and stalling issue



All times are GMT -5. The time now is 12:01 PM.