68 Chevelle LS Build
You have the P/N HAR-1084 harness which says it has the "2 CONNECTOR THROTTLE BODY"
http://secure.ultracart.com/catalog/.../HAR-1084.html
or the P/N HAR-1014 which uses the "SINGLE (8 PIN) CONNECTOR THROTTLE BODY"
http://secure.ultracart.com/catalog/.../HAR-1014.html
Im using the Nick Williams 102mm DBW TB.
Next is the options:
Im using the original LQ4 injectors, part# 25320288 so which one to choose from: Multech? EV1? EV6?
Oil pressure wiring: Yes? No?
AC: Yes
Coolant temp wiring: Yes? No?
Fuel level wiring: Yes? No?
And now the PCM
http://secure.ultracart.com/catalog/.../PCM-1003.html
Model? The engine is from a 2000 chevrolet silverado 2500 2WD with LQ4/4L80E
Intake? I got a Holley hi ram LS3/L92 ports
Fuel injector type: Im using the original LQ4 injectors, part# 25320288 so vortec truck?
You have the P/N HAR-1084 harness which says it has the "2 CONNECTOR THROTTLE BODY"
http://secure.ultracart.com/catalog/.../HAR-1084.html
or the P/N HAR-1014 which uses the "SINGLE (8 PIN) CONNECTOR THROTTLE BODY"
http://secure.ultracart.com/catalog/.../HAR-1014.html
Im using the Nick Williams 102mm DBW TB.
Next is the options:
Im using the original LQ4 injectors, part# 25320288 so which one to choose from: Multech? EV1? EV6?
Oil pressure wiring: Yes? No?
AC: Yes
Coolant temp wiring: Yes? No?
Fuel level wiring: Yes? No?
And now the PCM
http://secure.ultracart.com/catalog/.../PCM-1003.html
Model? The engine is from a 2000 chevrolet silverado 2500 2WD with LQ4/4L80E
Intake? I got a Holley hi ram LS3/L92 ports
Fuel injector type: Im using the original LQ4 injectors, part# 25320288 so vortec truck?
Andrew
It was memorial day when i posted that but i already called them and placed and order
Here is my order sheet:
'02 VORTEC W/ 4L60E STANDALONE WIRING HARNESS (DBW)
THROTTLE BODY TYPE: DRIVE BY WIRE (2 ELECTRICAL CONNECTORS ON THROTTLE)
INJECTOR TYPE: MULTEC INJECTORS
TRANSMISSION TYPE: 4L80E (ELECTRONIC AUTO) + $25
OIL PRESSURE WIRING (F-BODY GAGE CLUSTER ONLY): NO
AC RECOGNITION: YES + $15
CRUISE CONTROL: NO
COOLANT TEMP WIRING (F-BODY GAGE CLUSTER ONLY): NO
FUEL LEVEL WIRING (F-BODY GAGE CLUSTER ONLY): NO
MOD-1018: 6 PIN THROTTLE BODY MODIFICATION +25.00
PCM-1003: LS/VORTEC ENGINE PCM WITH PROGRAMMING
THROTTLE BODY TYPE: DRIVE BY WIRE
TRANSMISSION TYPE: 4L80E (ELECTRONIC AUTOMATIC)
ENGINE SIZE: 6.0
MODEL: TRUCK (SILVERADO/YUKON/SUBURBAN/VAN/SIERRA/ESCALADE)
INTAKE MANIFOLD TYPE: VORTEC TRUCK
ENGINE YEAR: 2000
FUEL INJECTOR TYPE: VORTEC TRUCK
TIRE SIZE: 275/40/18
REAR GEAR RATIO (X.XX):CUSTOMER/TUNER WILL UPDATE
Total $916.20
Now i have a question, im using the '07 Monte Carlo DBW pedal Pt# 15831256, the one you recommended for A-bodies on several forums. Do i need a TAC module? they offered me one along with a TCC/Brake switch kit but i was unsure and said ill check and get back to him later
Thanks
'07 Monte Carlo DBW pedal (Pt# 15831256) with 6 pins
PSI harness has accelerator pedal harness with 16 pins
Something im missing here?
Door gaps being checked
Floor pans had to be primered again for paint
Unfortunately, the regular hood wouldn't close with the Holley Hi-ram and tall and narrow mounts so i switched to the short and wide ones in the hope it will bring the engine down more but it was a no go.
Trimmed the X-brace on the underside of the bonnet but still didn't help so it either i get a Mid-ram or 2 inch cowl hood like toytech93 did. Im going to go with the Mid-ram and switch over the openings in order to retain the 102mm opening and the NW TB but i got the engine to run, ill try to upload a clip of that
The Best V8 Stories One Small Block at Time






