anyone interested in a procharged 3rd gen?
#1
On The Tree
Thread Starter
iTrader: (1)
Join Date: May 2004
Location: Mass
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
anyone interested in a procharged 3rd gen?
1985 Trans Am- 355 Procharged SBC built by golens. The body has 144k on it, the engine tranny and rear end have 1800 miles on them. I have owned it for 5 years now and have only put roughly 500 miles on it. Been sitting in storage the last 3 1/2 years. I start school in 3 weeks and i cant afford to store her anymore. The interior is stock w/ some 80's splatter paint BS the previous owner did
I know im in the wrong section but id rather it go to someone local who will take care i of her.
Heres what shes got.
SBC 355ci
KB Hyper Pistons
Eagle Rods
Federal Mogul Main and Rod bearings
Chromemoly pushrods
Comp Blower Cam
Federal Mogul Oil Pump
TCI Balancer
Sportsmen 2 heads
4-Core Aluminum Radiator
Procharger Small Block Chevy kit with P600B, Polished
Upgraded mechanical fuel pump
Modified Holley 650 CFM
Autometer Fuel Pres. and Boost Gauges on hood
Autometer 5 inch Tach on dash
B&M Th350
B&M Shift kit
B&M Torque Converter(wrong one!)I know the one it needs now.
Driveshaft Loop
10 bolt rear rebuilt
Richmond 4.10s
Auburn Posi Unit
Hedman Headers
1/2 *** true dual set-up(wanted to see if i could fit 2-2 1/2 inch pipes where 1 3 incher was.(Fits just hangs a little low)
It also has new cats on it.
2- 5 inch Supertrapp Muffs
Prime Aluminum Rims, 2- 15x7 and 2- 15x10
BFG Drag radials out back 275 60R 15
BFG Radial TAs in front 245 60R 15
10 disc changer
10 inch bass tube
Viper Alarm( must be taken out, eats batteries!)
Newer Blue paint
NO power steering
Power brakes
1 power window, 1 crank job
Last time it was weighed it was 3130lbs without driver
Parts not installed/ or needed.
Have:
3 Core intercooler w/L98 waste gate
MSD 6AL-BTM
Megashifter
SFC's
Need:
FRESH FUEL
Headliner
Electric Fans
Different Flywheel and Torque converter
Would Probably go with a Holeshot 3000?
Roll Bar/Cage
Misc suspension work, shes been sitting for a while.
I probably missed something, just ask if you've got questions.
Thanks for looking, Scott
I know im in the wrong section but id rather it go to someone local who will take care i of her.
Heres what shes got.
SBC 355ci
KB Hyper Pistons
Eagle Rods
Federal Mogul Main and Rod bearings
Chromemoly pushrods
Comp Blower Cam
Federal Mogul Oil Pump
TCI Balancer
Sportsmen 2 heads
4-Core Aluminum Radiator
Procharger Small Block Chevy kit with P600B, Polished
Upgraded mechanical fuel pump
Modified Holley 650 CFM
Autometer Fuel Pres. and Boost Gauges on hood
Autometer 5 inch Tach on dash
B&M Th350
B&M Shift kit
B&M Torque Converter(wrong one!)I know the one it needs now.
Driveshaft Loop
10 bolt rear rebuilt
Richmond 4.10s
Auburn Posi Unit
Hedman Headers
1/2 *** true dual set-up(wanted to see if i could fit 2-2 1/2 inch pipes where 1 3 incher was.(Fits just hangs a little low)
It also has new cats on it.
2- 5 inch Supertrapp Muffs
Prime Aluminum Rims, 2- 15x7 and 2- 15x10
BFG Drag radials out back 275 60R 15
BFG Radial TAs in front 245 60R 15
10 disc changer
10 inch bass tube
Viper Alarm( must be taken out, eats batteries!)
Newer Blue paint
NO power steering
Power brakes
1 power window, 1 crank job
Last time it was weighed it was 3130lbs without driver
Parts not installed/ or needed.
Have:
3 Core intercooler w/L98 waste gate
MSD 6AL-BTM
Megashifter
SFC's
Need:
FRESH FUEL
Headliner
Electric Fans
Different Flywheel and Torque converter
Would Probably go with a Holeshot 3000?
Roll Bar/Cage
Misc suspension work, shes been sitting for a while.
I probably missed something, just ask if you've got questions.
Thanks for looking, Scott
Last edited by LowBird; 02-13-2007 at 03:10 PM. Reason: remove pics
#6
On The Tree
Thread Starter
iTrader: (1)
Join Date: May 2004
Location: Mass
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
i never ran her at the track. previous owner said she ran low 10's for what its worth. Golens says the motor dyno'd at 475hp he didnt know torque, but thats before the new ignition and intercooler. I dont know how much more she'll make with those. But she can handle more boost. If i remember correctly shes running 8-9lbs right now. Id like to get $9,500 if i could (have to pay off my fourth gen,or sell that instead) my idiot neighbor hit the rear bumper with something and chipped some paint yesterday ill get a pic of that hopefully today. I have most of the build slips for the motor, rear end that i can fax to you guys. i cant copy and paste the pics.
try these. if not ill just email you some pics. the work computer doesnt like me right now.
anyone want her as a roller?
want the motor?
make offers
try these. if not ill just email you some pics. the work computer doesnt like me right now.
anyone want her as a roller?
want the motor?
make offers
Last edited by LowBird; 02-13-2007 at 03:14 PM. Reason: bad pics