methanol injection
methanol injection Just wondering how many of you guys are running meth kits on your turbo or supercharger engines?? Im looking at running one on my turbo setup and was wondering what kit you have and what you think about it..
Oh, and AlkyControl FTW.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
Teching In
Joined: Jun 2010
Posts: 39
Likes: 0
From: Bakersfield, Ca
Blown, got this right from the aem site.
AEM’s progressive controller has a unique system readiness failsafe called “Boost Safe” that monitors the entire injection system.dum If at any time the controller detects an error, the “Boost Safe” output will trigger a ground signal.dum The “Boost Safe” output will activate if there is a short, loss in continuity from a broken wire or bad connection, blown fuse, overheated pump, overheated pump driver, or a high or low voltage condition.dum The fluid tank comes fitted with a pre-installed low level switch and in the event the fluid level begins to get too low, the “Boost Safe” output will activate putting your engine into a safe mode before the system runs completely out of fluid.dum This failsafe function is an exclusive feature only available on the AEM Water/Methanol Injection System.
AEM’s progressive controller has a unique system readiness failsafe called “Boost Safe” that monitors the entire injection system.dum If at any time the controller detects an error, the “Boost Safe” output will trigger a ground signal.dum The “Boost Safe” output will activate if there is a short, loss in continuity from a broken wire or bad connection, blown fuse, overheated pump, overheated pump driver, or a high or low voltage condition.dum The fluid tank comes fitted with a pre-installed low level switch and in the event the fluid level begins to get too low, the “Boost Safe” output will activate putting your engine into a safe mode before the system runs completely out of fluid.dum This failsafe function is an exclusive feature only available on the AEM Water/Methanol Injection System.
I have the snow with the progressive controller with dual nozzle's it's great always works likes it's suppose too. I dunno why everyone hates on the snow, I guess it is more expensive than the others....
meth injection.... Not water, I had a kit in my car that had plastic water lines more at home under your kitchen counter, and i ran the lines from the trunk to the engine comparment as far as possible from the heat' yet they melted shot and about 3/4 inch wide, this micki mouse thing got to stop, if the lines are not braided and you got to mix, is not a meth kit, and does not belong in your car, methanol comes 99% pure and can be used strieght up with the real deal and will do every thing others pretend.
Must not lieve the meth in the system for prolong periods, just put an inline valve and disconect the pump side and ran water to clear the pump when car not in service, system can be purched by pressing the test button.
I made 940 wt and 800 whp on pump gas, using dual nossles, never a problem, Alkycontrol 813-265-1400, cause boost need so, and cost is about the same.
Must not lieve the meth in the system for prolong periods, just put an inline valve and disconect the pump side and ran water to clear the pump when car not in service, system can be purched by pressing the test button.
I made 940 wt and 800 whp on pump gas, using dual nossles, never a problem, Alkycontrol 813-265-1400, cause boost need so, and cost is about the same.
9 Second Club
iTrader: (10)
Joined: Apr 2009
Posts: 1,230
Likes: 3
From: Joliet,IL and Las Vegas 50/50
Does the alky control run of ofa boost/vac source to determine when to start injecting meth? Is it a pulse off of duty cycle or just sprays at different pressures?
im using a shure pump with two nozzles controlled by my efi box.
running tap water.
before injection i used to see 230 degree temps at 8.5psi
with the water injection temps are 155 at 15psi
with some ice cubes in the water, they are 125 at 15psi
running tap water.
before injection i used to see 230 degree temps at 8.5psi
with the water injection temps are 155 at 15psi
with some ice cubes in the water, they are 125 at 15psi
