mods help
Thread Starter
Staging Lane
Joined: Jan 2011
Posts: 97
Likes: 0
mods help I want to do a FAST 102/102 on top of the H/C and full exhaust kit. However the money is a little bit more than id like to spend. However selling 241's LS6 intake complete with TB rails and injectors. What kind of money can i expect out of these?
^$150 for an LS6 intake?? 0_o Those go for $300-$350 all day. Rails and injectors is reasonable at $100 for stock, then add $50 for the TB. Even that would be a tad high for a non-ported TB. I got $75 for my P+P'd TB (was a worked over SLP stocker.) 241's are decent and worth porting and can prolly fetch around $250.
$450 shipped for LS6 intake, TB, rails and injectors; complete.
241's?? hmmm... $280 + shipping.
$450 shipped for LS6 intake, TB, rails and injectors; complete.
241's?? hmmm... $280 + shipping.
Last edited by bayer-z28; Feb 18, 2011 at 08:44 PM.
^ Expect $700. And wathcout for the ones around here that like to low-ball you. One offered me $200 shipped for my LS6 intake. Noooo.
And be prepared to do another $500-$800 (depending) over that for the TB, lid, MAF, injectors, Lines, Rails, Valley cover bolts (Maybe LS6 valley) and ducting. Just harass the Classifieds..
Saved me a PANTload. 
I did the same thing this winter for my 102 swap. Sold all my stock stuff and an extra LS1 intake to help fund it.
And be prepared to do another $500-$800 (depending) over that for the TB, lid, MAF, injectors, Lines, Rails, Valley cover bolts (Maybe LS6 valley) and ducting. Just harass the Classifieds..
Saved me a PANTload. I did the same thing this winter for my 102 swap. Sold all my stock stuff and an extra LS1 intake to help fund it.
^ The LS6 valley cover is pure preference. It's a different PCV system and personally, I don't want ANY oil getting sucked through my new intake. SO I am switching to the different PCV system, and a BETTER PCV system. Thunder Racing has the whole "kit" for it. Valley cover, gaskets, 180* tubing, bolts and caps. Good deal, IMO even though I don't need the bolts.
For the MAF, go with an 85mm Delphi unit. Check the classifieds pretty often, you should find one. And they sell them on Ebay for around $75 and up. And make sure you get the pig-tail with it.
For the MAF, go with an 85mm Delphi unit. Check the classifieds pretty often, you should find one. And they sell them on Ebay for around $75 and up. And make sure you get the pig-tail with it.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
