Poly engine mounts?????
Thread Starter
TECH Addict
iTrader: (5)
Joined: Jan 2003
Posts: 2,298
Likes: 0
From: Fuquay-Varina, NC
Poly engine mounts????? Of course since my Jet hot lt's and hooker modded Y were installed my Y bangs the floor. Should I get poly mounts or does GM offer 1le's? I had the "ghetto" motorcycle ratchet strap in place but it ran behind the steering rack and I could feel that affect my steering on WOT. I couldn't figure a better way to route it. I was thinking one poly mount on one side and see how that does. When I had the poly trans mount in, that lasted the 30 minute drive home before I yanked it off.
Thread Starter
TECH Addict
iTrader: (5)
Joined: Jan 2003
Posts: 2,298
Likes: 0
From: Fuquay-Varina, NC
I searched for lle's and couldn't find them anyway. Went to 1le.net and didn't see a part # listed. I hope they don't make the awful sound the trans mount did.
Thread Starter
TECH Addict
iTrader: (5)
Joined: Jan 2003
Posts: 2,298
Likes: 0
From: Fuquay-Varina, NC
Wishing I had the extra cash to have bought some when I did my headers. At least I know my way around the engine bay very well now. I was thinking trying the dr side only first. Thanks Lynda.
Originally Posted by Redlinez
Wishing I had the extra cash to have bought some when I did my headers. At least I know my way around the engine bay very well now. I was thinking trying the dr side only first. Thanks Lynda.
Lynda
Launching!
Joined: May 2004
Posts: 260
Likes: 0
Originally Posted by CamaroCain
well, since i only installed one, i still have the other one, i will talk it over with the hubby and see if he will let me sell it. Shoot me a PM if you are interested.
Lynda
Lynda
Thanks
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Originally Posted by LeddySS98
Is this hard to do? How long did it take you to put them in? Why would you/did you ONLY do the DS?
Thanks
Thanks
I think it would take quite a bit longer to put one in from scratch, but we already had the headers off, so it wasnt too bad. We only put the drivers side in because we are also trying to keep as much vibration out as possible, with one poly in and one stock one in, you have a little more give than having both poly in.
Some peaple likes there car to sound like a hot rod but if you like to feel a hot rod then the ProThaine mount is what you want.and if you have a loop cam then you car will shake the ground.I love mine it stiffend up the motor, and i put one on the trans ,now the exhaust don't move ,but the whole car does.I have a big cam to 595"-600"/232-236/110LSA .I put them on both pass/driver side.
