how loud are they? 
TSP installed!
ok, i know this might sound like a stupid question, but, do the tsp true duals bolt up to the pacesetter headers, or the pacesetter y-pipe...b/c i have magnaflow cat-back on now, and pacesetter headers waiting to go on...wondering if i should sell the magnaflow and pacesetter y-pipe and get the true duals
Thread Starter
TECH Enthusiast
Joined: Apr 2004
Posts: 577
Likes: 0
bolt right up the the pacsetters, you will have no cats or anything, its cool, everyone has been there once and a while! It replaces all the piping and no magnas any more. Get the true duals for more power and sound!!!
Trending Topics
Thread Starter
TECH Enthusiast
Joined: Apr 2004
Posts: 577
Likes: 0
Ya, the whole system just bolts up to the headers(pacesetters). I like that they paint the tubing, it keeps the exhaust temps down and the bends are great, a lot of time went into making that system!
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Glad you like it 
We spent alot of time getting them so they would install pretty easy
We spent alot of time getting them so they would install pretty easy
__________________
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
what about the bmr ds loop and torque arm clearance issues...i am going to get it either way, i am convinced, but i need to run a ds loop becasue i run at route 66 and they look everytime...thanks
Thread Starter
TECH Enthusiast
Joined: Apr 2004
Posts: 577
Likes: 0
I was planning on gettinga BMR torque arm, but waiting until i go back to lubbock to ask questions and look at the cars from texas speed(thats where they are located). I will make a post prob in a week or two about the install.
Do you have any clips of that yet? One of my buddies, as well as myself, are trying to decide on purchasing the TSP TD's. I have searched on this site for sound clips and have also looked at ls1sounds. Any clips would be great from anyone with these! Thanks
FWIW, it has been confirmed that these TD's will also directly bolt up to QTP's and Kooks. I finally got them to work on my Kooks (after 4 tries cause I'm an idiot) and they sound awesome. I'm sure they are louder than my LM was, but they are so deep and refined with the bullets that it doesn't really seem loud at all. It's pure music.
