Long tubes
TECH Fanatic
iTrader: (4)
Joined: Jul 2003
Posts: 1,075
Likes: 0
From: Orange Park/ Jacksonville, FL
Originally Posted by conan
KOOK'S or QTP'S
Just get you a set of Armor coated Pacesetter LT's for under $400 shipped to your door. Best bang for the buck & if you dont live on a coast or in a snowy state dont even worry bout wastin money on stainless.
Originally Posted by JBIRD02
hes right, most regard these as the 2 best headers available, however they are the 2 most expensive. I have the jet hot headers, and am happy so far, but if I had it to do over, I'd get the Edelbrock's. Too bad they werent out when I bought my headers
Trending Topics
Originally Posted by DBeck
damn, $700+...is it worth it?
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
TECH Enthusiast
Joined: May 2005
Posts: 555
Likes: 0
From: Blairsville, GA
Why Edelbrock???
Welp, they're around $400, they're 1 3/4" stepped to 1 7/8", they go in pretty easy, and their Ti-tech coating is supposed to be pretty good, too. Not that I have a set, I'm just passing along what I've heard about'em.
Welp, they're around $400, they're 1 3/4" stepped to 1 7/8", they go in pretty easy, and their Ti-tech coating is supposed to be pretty good, too. Not that I have a set, I'm just passing along what I've heard about'em.
TECH Fanatic
iTrader: (4)
Joined: Jul 2003
Posts: 1,075
Likes: 0
From: Orange Park/ Jacksonville, FL
Originally Posted by Ric
Why Edelbrock???
Welp, they're around $400, they're 1 3/4" stepped to 1 7/8", they go in pretty easy, and their Ti-tech coating is supposed to be pretty good, too. Not that I have a set, I'm just passing along what I've heard about'em.
Welp, they're around $400, they're 1 3/4" stepped to 1 7/8", they go in pretty easy, and their Ti-tech coating is supposed to be pretty good, too. Not that I have a set, I'm just passing along what I've heard about'em.
Originally Posted by JBIRD02
yep, thats about it, he beat me to it! and from what I was told, they also have the HVMC like the qtp's do.
11 Second Club
Joined: Feb 2003
Posts: 5,524
Likes: 1
From: The South
https://ls1tech.com/forums/showthread.php?t=139142
And search, this question has been gone over hundreds of times before.
Personally I'd go with coated pacesetters, but I am always on limited funds.
And search, this question has been gone over hundreds of times before.
Personally I'd go with coated pacesetters, but I am always on limited funds.
TECH Fanatic
iTrader: (4)
Joined: Jul 2003
Posts: 1,075
Likes: 0
From: Orange Park/ Jacksonville, FL
Originally Posted by DBeck
So which one would you go with?