Pacesetter LT Install PICS

Reply Subscribe

Thread Tools

Search this Thread

Jan 28, 2007 | 10:43 AM

brifri

Thread Starter

Teching In

Joined: Oct 2004

Posts: 32

Likes: 0

Pacesetter LT Install PICS

Well since cats were gone already my car wont pass emissions so i decided it was time for a tune and i needed something done on the car. so here we are
They came a week ago and been waiting for access on a lift.
But i had to do some modifications to the inside of the y pipe.
before
http://new.photos.yahoo.com/reprogle...804204038659/9
http://new.photos.yahoo.com/reprogle...804204030161/8
after
http://new.photos.yahoo.com/reprogle...804204061465/5
http://new.photos.yahoo.com/reprogle...804204038907/4
more to come

Jan 28, 2007 | 10:51 AM

dpw41285

TECH Resident

iTrader: (26)

Joined: Apr 2006

Posts: 969

Likes: 0

From: Ft Wayne, IN

what did you use to get in there and clean it up

Jan 28, 2007 | 10:53 AM

Red99TA

TECH Addict

iTrader: (11)

Joined: Oct 2003

Posts: 2,442

Likes: 6

From: Topeka, KS

Very nice...what did you use to reach down there and cut it?

Jan 28, 2007 | 11:25 AM

brifri

Thread Starter

Teching In

Joined: Oct 2004

Posts: 32

Likes: 0

i put new ngk 55s in while they were gonig back in 60,000 its probably time.
only thing i had to take off was a shield and the oil filter. on the driverside

http://new.photos.yahoo.com/reprogle...804204048183/6 new compared to old
http://new.photos.yahoo.com/reprogle...804204061560/3 driverside out
http://new.photos.yahoo.com/reprogle...804204070412/2 passenger side in (easy)
http://new.photos.yahoo.com/reprogle...804204061662/0 driverside in
open header clip
http://video.ls1tech.com/video/9c338...c400ccc343.htm

Jan 28, 2007 | 11:29 AM

brifri

Thread Starter

Teching In

Joined: Oct 2004

Posts: 32

Likes: 0

i used a straight die grinder with a sanding wheel cut down smaller than 3"
also used a drill with a rotory file on the end. ill take pic when i finish it up today.

Jan 28, 2007 | 01:06 PM

studderin

TECH Senior Member

iTrader: (28)

Joined: Nov 2005

Posts: 5,556

Likes: 6

From: Rochester, NY

wow that Y looks really good. looking at seeing the other pics

Jan 28, 2007 | 01:26 PM

streetlegalls1

On The Tree

iTrader: (15)

Joined: Aug 2006

Posts: 149

Likes: 0

From: Louisiana

Gives me hope for mine when they come in this week,well done

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Awesome K5 Blazer Restomod Comes With C7 Corvette Power

Verdad Gallardo

10 Camaros You Should Never Buy

10 LS Engine Myths That Refuse to Die

Verdad Gallardo

Jan 28, 2007 | 07:30 PM

brifri

Thread Starter

Teching In

Joined: Oct 2004

Posts: 32

Likes: 0

i drove it to the gas station and didnt get on to hard but it pulls harder in the higher rpms. i think once i do the ls7 clutch and 4:10 gears it will be about done for now.
One problem i got is the driverside y hits the floor where its flattened maybe i didnt center but its a tight fit under there.
Now its time for the tune.