Kooks header install thread?
Kooks header install thread? I will be installing some kooks 6500rhs headers b4 long with a ORY and wondered if anyone had a nice install thread? Not like I never installed headers b4 but I would like to know all the issues and things b4 hand that I might have. Also what plugs and wires do most people use?
I put in a set of Kooks SS headers and ORY this past weekend. Install went great.
Just make sure you have the car way up in the air...mine was probably ~2ft in the air from K-member to the ground.
I don't know that I've ever seen an install thread for them, but it's relatively straight forward.
One tip I can offer you to make it easier is to ZIP tie the gasket loosely to the flange through a couple bolt holes. This make it easier being that you have one less thing to try and hold on to. Also, then the gasket holes are lined up correctly with the holes in the flanges. Then when you have a couple bolts started, just snip the ZIP ties and finish running the rest of the bolts in.
I actually put mine in by myself....was frustrating at times, but went pretty smooth overall.
Good luck.
Just make sure you have the car way up in the air...mine was probably ~2ft in the air from K-member to the ground.
I don't know that I've ever seen an install thread for them, but it's relatively straight forward.
One tip I can offer you to make it easier is to ZIP tie the gasket loosely to the flange through a couple bolt holes. This make it easier being that you have one less thing to try and hold on to. Also, then the gasket holes are lined up correctly with the holes in the flanges. Then when you have a couple bolts started, just snip the ZIP ties and finish running the rest of the bolts in.
I actually put mine in by myself....was frustrating at times, but went pretty smooth overall.
Good luck.
Unfortunately I didn't take any "in-progress" pics...but I could get you some of the finished product if that helps.
I used the gaskets that came with the Kooks...but I think either those or the stockers would be fine.
I used the gaskets that came with the Kooks...but I think either those or the stockers would be fine.
https://ls1tech.com/forums/generation-iii-external-engine/406318-my-long-review-qtp-1-3-4-lt-s-tsp-3-true-dual-system-lots-o-pics.html
http://www.geocities.com/foff667/98Camaropg4.html
Hope those help you out with the install.
No use on swapping the wires if they look good still, the stockers are fine...same with the header gaskets.
http://www.geocities.com/foff667/98Camaropg4.html
Hope those help you out with the install.
No use on swapping the wires if they look good still, the stockers are fine...same with the header gaskets.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Gifts Neither Your Dad Nor Grad Will Shove Into the 'Trinket Drawer'
Brett Foote
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Originally Posted by dirty2kTA
the zip tie idea is pretty clever, but i didn't have problem with holdin the gasket in place by hand.
I need four hands and six elbows sometimes when working on this car!
