smooth bellows?
Thread Starter
10 Second Club
iTrader: (2)
Joined: Aug 2003
Posts: 1,744
Likes: 0
From: Houston,Texas/College Station
smooth bellows? if i order the cold air induction kit would the bellows be worth to order too and how much real horsepower am i lookin at if i get slp smooth bellows, thanks guys
TECH Fanatic
Joined: Jun 2003
Posts: 1,070
Likes: 0
From: Further South than Hell
Re: smooth bellows? Do a search on "Bellows" in the forum. There is a lot on same topic. Quite a few poeple made theirs from Home Depot flexible tubing for next to nothing.
I wouldn't spend what suppliers ask fo them.
I got FIPK and bellows come with it.
I wouldn't spend what suppliers ask fo them.
I got FIPK and bellows come with it.
Re: smooth bellows? Re: smooth bellows?
What Inside Diameter hose are you guys using. I heard that the 3 inch would work, but it does not even come close to fitting on my car.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo
TECH Resident
Joined: Sep 2002
Posts: 803
Likes: 0
From: Charlotte, North Carolina
Re: smooth bellows?
I got this one..... Airflow Systems Inc. ....beats paying $50
Re: smooth bellows?
Nice bellow NightHawk.
Rock on Donate52
ZeeQuick, the 3" to 3" fernco works, you just have to trim it a little. Check out that link just above the picture that I posted. If its trimmed properly, you don't even have to microwave it
Re: smooth bellows? At home Depot the 3" fernco coupler fits perfect...no need for ends to be different..and It costs $5-$7....and every city has a home depot or a plumbing store that has one of these....
It fits perfect...and snug...just heat the dam thing in the nicrowave for about 45 seconds and it flexes a little easier....then drive around and get the car good and hot and it will flex itself into place a little more...when it cools down...It fits perfect...some people have had o shave off the top side of the end connecting to their MAF because of the angle...but its fairly soft rubber...and is easy to cut if you have a "sharp" knife...and you can ppick it up insted of having to order it and wait for it to show up...I put mine on in the parking lot of home depot.
It fits perfect...and snug...just heat the dam thing in the nicrowave for about 45 seconds and it flexes a little easier....then drive around and get the car good and hot and it will flex itself into place a little more...when it cools down...It fits perfect...some people have had o shave off the top side of the end connecting to their MAF because of the angle...but its fairly soft rubber...and is easy to cut if you have a "sharp" knife...and you can ppick it up insted of having to order it and wait for it to show up...I put mine on in the parking lot of home depot.
