Anyone use ARP header studs ?
Anyone use ARP header studs ? Has anyone used the ARP header studs ? How did you like them ? Were they easy to install? any issues?
There will be used for a 06 GTO with kook's long tube headers. Hoping they will be easy to install
There will be used for a 06 GTO with kook's long tube headers. Hoping they will be easy to install
This is what I used. I know it says oil pan but they work perfect for headers too. Stainless steel and inexpensive.
http://cgi.ebay.com/ebaymotors/LS1-L...lenotsupported
http://cgi.ebay.com/ebaymotors/LS1-L...lenotsupported
This is what I used. I know it says oil pan but they work perfect for headers too. Stainless steel and inexpensive.
http://cgi.ebay.com/ebaymotors/LS1-L...lenotsupported
http://cgi.ebay.com/ebaymotors/LS1-L...lenotsupported
I didnt want to put the money out for the studs cause im low on cash right now. But if these work im going to order them
Last edited by BigRich954RR; Jun 22, 2009 at 09:02 PM.
I went with ARP studs on my Camaro when I swapped from 1-3/4" to 1-7/8" headers. Unfortunately, the install advice I have is only related to the F-body...I'm not sure what the clearance is like on the GTO when installing headers.
For the F-body, you can pre-install each and every stud in the head on the passenger side and still have enough room to get the header in place without interference. The driver's side, though, you couldn't install even one and get the header to slide in place. You just kinda have to watch where the headers need to go in relation to the heads as you slide the headers up to see if there will be any clearance issues with pre-installed studs.
Other than that, I love mine. They look great, and sealed everything up as they should. Pricey bastards though...
For the F-body, you can pre-install each and every stud in the head on the passenger side and still have enough room to get the header in place without interference. The driver's side, though, you couldn't install even one and get the header to slide in place. You just kinda have to watch where the headers need to go in relation to the heads as you slide the headers up to see if there will be any clearance issues with pre-installed studs.
Other than that, I love mine. They look great, and sealed everything up as they should. Pricey bastards though...
One more thing to add, I use hi temp anti seize on the threads going in to the heads, I use a hex bit and bottom out the stud and then back it off a little bit. I have removed them and reinstalled them several times with no problems. They look like the day I bought them.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
recessed into the stud.
lil allen key. i think i used a 10 or 15 torx driver so i wouldnt put them in too tight.
im my 3rd gen, i can do all the drivers side, only a couple on the passenger side, i have a pretty tight header clearance issue there.
still makes it easier to get the header and gasket lined up and they look bitchin'.
ive had tons of compliments on them from racers to waxers.
just finishes out the look, IMO.
they arent needed, and a complete waste of money, unless your an addict.
lil allen key. i think i used a 10 or 15 torx driver so i wouldnt put them in too tight.
im my 3rd gen, i can do all the drivers side, only a couple on the passenger side, i have a pretty tight header clearance issue there.
still makes it easier to get the header and gasket lined up and they look bitchin'.
ive had tons of compliments on them from racers to waxers.
just finishes out the look, IMO.
they arent needed, and a complete waste of money, unless your an addict.
