Yeah but that's different from an ls1 he was saying that there called ls1's also when there actually called lq4 or lq9. I have a 6.0 iron block that'd going in my car...

 

Oh my god! This is awesome! And by the way, I have actualy SEEN some one USE the cam install hammer.Hahahahahahahahahahahahah. Hahaha. Then sand the bearings and finally give in, and take it and have it line honed. Hahahahahahahahahaha

 

Cam bearings have been bent or crushed from installing with a hammer or you have the wrong cam..

You don't have to know anything about automotive to be the shop teacher..you just have to have a teaching degree. I have my ASE master Tech and a Degree in Mechanical engineering, but I was told I couldn't be the shop teacher at Cy-Fair, unless I got a teaching degree..

 

Lmao you all will die when I tell you this... He is an ASE master tech Lmao -_-

 

Hahahahahahahahahaha. Baaaahahahahahaha
Awesome

 

the cam bearings are screwed up from being installed incorrectly.

 

Ive seen this happen a rare few times. If the engine is on a stand after a while the block twists because its only supported on one end. Put the block on the floor and let it sit there for a bit and then try again.

 

"Most of the time" ASE = Ask Someone Else. That was the running joke for a long time. Anyone with a working mind can buy a study book and pass a test.

 

WoW... well at least you have the knowledge to know better.

What he is doing is wrong.

 

What school is this? U should sue. Poor ls1, save it!

Probably bent the edges of the bearings when he put them in and the cam won't fit. :/ use a grinder and grind the bearing down a bit and wala! If he asks why, just say it's faster then using sand paper by hand.

 

This is my high school program... He's been doing this for over 45 years lol. I think he's starting to lose it... The said thing is this class is worth 12 college credits also haha. Oh well I only have to be here another 3 weeks idk how I'm going to get the cam in Monday. I might just take the bearings out and put the cam in and say "ok its in there haha" Il get my grade and be long gone before it gets torn down again haha maybe Il leave the bearings in the oil pan for the next students and right good luck on 1 of them haha.

 

wow that teacher is one weird dude...ask him if you can try puttin a gen 1 cam in it instead lol

 

Lol. While I'm talking about my retarded instructor... I might as well tell you about the retarded students haha. This 1 kid took the bumper off to change the spark plugs haha. The same kid today had his tool box rolled over by the 4 post alignment lift. He had the top of his toolbox hanging over the lift. The box has a top on it longer then the box. Some kid starts raising the lift and then you hear a funny cracking noise and there goes the top of his box Lmao the lift took the top basicly off the box hahaha. This other kid thought a turbo was spooled by the air coming into the intake not the exhaust gases lol. The same kid couldent figure out where the crankshaft was... I'm going to walk away feeling good that I made it out alive haha.

 

Yeah ASE means jack ****. I've seen the questions. It just makes you look better in the public eye

 

This thread is like a high speed train wreck. Even today I had to come back and see. Hahahahahahahahahah.

 

Nobody said getting the ASE was hard. Unfortunately, you have to take their stupid tests to get paid anything in the automotive world.

 

I think my x business partner has found a job teaching at your school.

 

can you take a picture of your issue?

 

whatever school that is they are running a great operation...its a shame they had to destroy an ls1

 

So true about the pay for being ASE.