View Poll Results: What type of Connecting Rods?
Multiple Choice Poll. Voters: 272. You may not vote on this poll
Poll: I-Beam or H-Beam?
Why do people think stock rods are weak? I've been making about 700 hp on mine for 10k+ miles. My friends car has about 700 on his stock rods and another friends car has 600 on his. These are also all high milage motors 70k+. All of the mentioned cars are turbo cars and all have stock bottom ends.
The stock pieces are not weak. We will be pushing one of the cars as far as it will go this year. I'm thinking we can break 900 rwhp with just upgraded rod bolts.
The stock pieces are not weak. We will be pushing one of the cars as far as it will go this year. I'm thinking we can break 900 rwhp with just upgraded rod bolts.
Originally Posted by Zombie
Why do people think stock rods are weak? I've been making about 700 hp on mine for 10k+ miles. My friends car has about 700 on his stock rods and another friends car has 600 on his. These are also all high milage motors 70k+. All of the mentioned cars are turbo cars and all have stock bottom ends.
The stock pieces are not weak. We will be pushing one of the cars as far as it will go this year. I'm thinking we can break 900 rwhp with just upgraded rod bolts.
The stock pieces are not weak. We will be pushing one of the cars as far as it will go this year. I'm thinking we can break 900 rwhp with just upgraded rod bolts.
So if that's the case-if i were to build a budget 346 can i just use the stock rods-polish the beams and use some forged pistons? Would that be good for 650-700 rwhp?
Thread Starter
TECH Apprentice
Joined: Jul 2005
Posts: 327
Likes: 0
Budget motor IMO=
Stock Crank - $75 for polishing
Stock Rods - Free
ARP Bolts though - $100
Diamond or Mahle Pistons - $600
FM or Clevite Bearings - $100
ARP Head Bolts - $125
5.3L Heads and 918 springs- $500
Your choice of cam I like the voodoo cams for street use - $400
Pacesetter Coated LT's - $450
Cut-out - $75
Lid - $100
ls6 intake for pre 2001 ls1's - $350
ported tb - Free
de-screened MAF (? the effectiveness of this) - Free
Not too bad I don't think. Just a quick guess on the prices, heads may be off a little. And that should be good for 400-475 rwhp depending on tune from what I have seen in my own and other cars. And price isn't too bad either considering. One way to lower cost is to go with ls6 springs, buy a used cam, used headers, may already have an ls6 intake but do not skip this step, and that's about all I can think of right off the bat. Auto cars will need a stall and Man cars will eventually need clutches. Then both sooner or later will need a 12 bolt or 9" rear.
Stock Crank - $75 for polishing
Stock Rods - Free
ARP Bolts though - $100
Diamond or Mahle Pistons - $600
FM or Clevite Bearings - $100
ARP Head Bolts - $125
5.3L Heads and 918 springs- $500
Your choice of cam I like the voodoo cams for street use - $400
Pacesetter Coated LT's - $450
Cut-out - $75
Lid - $100
ls6 intake for pre 2001 ls1's - $350
ported tb - Free
de-screened MAF (? the effectiveness of this) - Free
Not too bad I don't think. Just a quick guess on the prices, heads may be off a little. And that should be good for 400-475 rwhp depending on tune from what I have seen in my own and other cars. And price isn't too bad either considering. One way to lower cost is to go with ls6 springs, buy a used cam, used headers, may already have an ls6 intake but do not skip this step, and that's about all I can think of right off the bat. Auto cars will need a stall and Man cars will eventually need clutches. Then both sooner or later will need a 12 bolt or 9" rear.
The biggest reason to not use the stock rods is finding pistons that fit the stock rod and bore. The other down side is resizing them since they are a cracked rod.
My new motor is a 370 and I'm using eagle SBC I-beams ($270) with some used forged diamond pistsons I got for $200.
I just wanted to point out that stock parts are not weak. Parts don't break from power for the most part, they break from mistakes such as detonation and oiling issues.
My new motor is a 370 and I'm using eagle SBC I-beams ($270) with some used forged diamond pistsons I got for $200.
I just wanted to point out that stock parts are not weak. Parts don't break from power for the most part, they break from mistakes such as detonation and oiling issues.
Thread Starter
TECH Apprentice
Joined: Jul 2005
Posts: 327
Likes: 0
Well with more power the chance of a detonation or oiling issue is a whole lot more dramatic. More power will show you the weakest link in your motor. I would say the weakest link in the ls1 is either the rod bolts, or I believe the pistons. In the motor anyway, as far as drivetrain, I'd say clutch or rears. I had both go out at about the same time (2 weeks apart, clutch first). But my pistons went way before they did, actually a detonation issue with n2o, and floating valves, a whole other story.
TECH Resident
Joined: Dec 2004
Posts: 881
Likes: 1
Originally Posted by Tony Mamo @ AFR
The quality of the rod is key....Ive seen killer versions of both. Metal integrity, quality control, machining tolerances, and obviously including a good rod bolt make for a good (and sometimes expensive) connecting rod. Its more of a personal preference amongst engine builders IMHO, and the reality is that a quality piece of either design will get the job done. The Callies Comp Star you mentioned is an excellent rod for the money....I just installed a set in the 383 I just completed dyno testing with. It had nice machining and was repeatable from one rod bore to the next when I checked them all with a dial bore guage.
Lunati, Manley, Eagle, Scat all make good stuff for the dollar spent. Some are a few bucks more but any of them (if assembled correctly) can reliably put up with alot of power and make a good upgrade over a factory rod even if you put in the better bolts (which certainly helps the stock piece put up with more power and RPM before failure).
I'm not voting because I dont feel one design is necessarily superior to the other....
Tony M.
Lunati, Manley, Eagle, Scat all make good stuff for the dollar spent. Some are a few bucks more but any of them (if assembled correctly) can reliably put up with alot of power and make a good upgrade over a factory rod even if you put in the better bolts (which certainly helps the stock piece put up with more power and RPM before failure).
I'm not voting because I dont feel one design is necessarily superior to the other....
Tony M.
In theory, an I-beam rod had bending stiffness in the direction where the pin and journal are rotating, not contributing bending forces. The H-beam has stiffness in this access. However, the strength is more complicated than just adding metal. So buying from a known vendor whose parts have been used and raced by people with combinations similar to or more abusive than yours is important. These manufacturers have developed their designs from experience, which may have included failures. For example, how many rods have you seen fail around the beam? How many around the rod bolt or pin?
Weight isn’t always a sign of designed in strength. Crower Maxi-Lights are sized for specific journal and pin sizes. Other rods frequently use one blank for different sizes. They end up with small journal/pin sizes weighing more than their large journal/pin cousins do.
The various sections of a rod can only be made so thin. H-beams have two sections along the rods longest dimension and can only take so much off the center. There are crossbeam rods that have a cross-shaped cross section. These rods claim the thicker material handles drilling an EDM pin oiling hole easer.
However, we live in the real world, and if you are spending $600 for a set, the Compstar, Eagle and SCATs are H-beam.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo
Teching In
Joined: Mar 2006
Posts: 25
Likes: 0
From: merrick new york
i didnt feel like reading everything but the majority of high end companies offer their 1000+ hp rods as i beams. and they are all %100 american made not some cheap overseas material machined here. crower, oliver, lentz, and even howards rods are offered as i beams. as far as what you should choose go for the lightest longest rod you can use depending on the hp requirements. if you can find a 550 gram rod that will hold up to 700hp as opposed to a 650 gram rod go for the 550 gram rod. usually the lighter rods tend to be i beams anyway....it all depends on your application. dont base anything on looks alone
Thread Starter
TECH Apprentice
Joined: Jul 2005
Posts: 327
Likes: 0
So...what we have learned here is....
no matter what the papers, sponsors, techies on the board, you or me say, it is still a matter of opinion. I'd say you're okay with either I or H beams, as long as they are a good quality material, and they fit your plans. Spend your money accordingly. Personally, I'd say H beam, just because I can, lol.
no matter what the papers, sponsors, techies on the board, you or me say, it is still a matter of opinion. I'd say you're okay with either I or H beams, as long as they are a good quality material, and they fit your plans. Spend your money accordingly. Personally, I'd say H beam, just because I can, lol.
Originally Posted by 2000_LS1
So...what we have learned here is....
no matter what the papers, sponsors, techies on the board, you or me say, it is still a matter of opinion. I'd say you're okay with either I or H beams, as long as they are a good quality material, and they fit your plans. Spend your money accordingly. Personally, I'd say H beam, just because I can, lol.
no matter what the papers, sponsors, techies on the board, you or me say, it is still a matter of opinion. I'd say you're okay with either I or H beams, as long as they are a good quality material, and they fit your plans. Spend your money accordingly. Personally, I'd say H beam, just because I can, lol.
Teching In
Joined: Jan 2006
Posts: 19
Likes: 0
Several years ago Hot Rod magazine had an engineer calculate the rod loads for the 4 cycles. The highest was on the exhaust stroke where there is a very small compression load when pushing the exhaust out that is overwhelmed by a huge inertia load from the piston mass, the pin knuckle and the pin when the crank reaches TDC and the aforementioned masses try to keep going straight up the cylinder bore. This puts tensile stress into the rod which can be handled by any shape crosssectional area and the rod material's yield (tensile) strength(psi). During the power stroke where maximum compressive loading occurs, the rod has to be analized as a column to prevent buckling, which is why the crosssection is either an "I" or an "H". 
Thread Starter
TECH Apprentice
Joined: Jul 2005
Posts: 327
Likes: 0
Well, I think you COULD spend more on H-Beams if you really wanted to...and you COULD spend twice as much on some I's. In the end, it's about user preference I would say. I like either...til one gives me a reason not to like it anymore.
Thanks for the input guys.
Thanks for the input guys.
On The Tree
Joined: Oct 2005
Posts: 160
Likes: 0
From: PNW
I would go with the I-beam and the lightest rod possible. The heavier the rod, the more stress is on it. At 6000-7000 rpm a rod can have the dynamic weight
(G-force) of about 8000 -10000 pounds. The lighter you can make the rod, the better.
(G-force) of about 8000 -10000 pounds. The lighter you can make the rod, the better.
