Generation III Internal Engine 1997-2006 LS1 | LS6
Sponsored by:
Sponsored by:

Torque Sequences

Thread Tools
 
Search this Thread
 
Old 09-23-2007, 07:25 AM
  #1  
Launching!
Thread Starter
iTrader: (3)
 
Eddie 70's Avatar
 
Join Date: Jan 2007
Location: Kingston Tn
Posts: 238
Likes: 0
Received 0 Likes on 0 Posts
Default Torque Sequences

I am getting ready to do a head swap on my project. Where can I find the correct torque sequence for the heads and intake at?

Thanks for any help.
Old 09-23-2007, 07:41 AM
  #2  
Launching!
Thread Starter
iTrader: (3)
 
Eddie 70's Avatar
 
Join Date: Jan 2007
Location: Kingston Tn
Posts: 238
Likes: 0
Received 0 Likes on 0 Posts
Default

I found a pic of the head that has what I was looking for. Now for the intake.

Old 09-23-2007, 07:43 AM
  #3  
TECH Fanatic
iTrader: (12)
 
Grifter's Avatar
 
Join Date: Dec 2006
Posts: 1,524
Likes: 0
Received 5 Likes on 5 Posts

Default

I was just about to post that. Here's the tighten sequence:

Tighten the cylinder head bolts.
Tighten

Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N·m (22 lb ft).
Tighten the M11 cylinder head bolts (1-10) a second pass in sequence to 90 degrees using the J 36660-A .
Tighten the M11 cylinder head bolts (1-8) to 90 degrees and the M11 cylinder head bolts (9 and 10) to 50 degrees a final pass in sequence using J 36660-A .
Tighten the M8 cylinder head bolts (11-15) to 30 N·m (22 lb ft).
Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
Old 09-23-2007, 07:48 AM
  #4  
Launching!
Thread Starter
iTrader: (3)
 
Eddie 70's Avatar
 
Join Date: Jan 2007
Location: Kingston Tn
Posts: 238
Likes: 0
Received 0 Likes on 0 Posts
Default

And the intake manifold torque sequence.

Old 09-23-2007, 08:11 AM
  #5  
TECH Fanatic
iTrader: (12)
 
Grifter's Avatar
 
Join Date: Dec 2006
Posts: 1,524
Likes: 0
Received 5 Likes on 5 Posts

Default

Do you have the actual tightening sequences too, or do you need them?
Old 09-23-2007, 08:15 AM
  #6  
Launching!
Thread Starter
iTrader: (3)
 
Eddie 70's Avatar
 
Join Date: Jan 2007
Location: Kingston Tn
Posts: 238
Likes: 0
Received 0 Likes on 0 Posts
Default

Originally Posted by Grifter
Do you have the actual tightening sequences too, or do you need them?

Post them up and I can print the whole thread off when I get to work. That would be great.
Old 09-23-2007, 09:28 AM
  #7  
TECH Fanatic
iTrader: (12)
 
Grifter's Avatar
 
Join Date: Dec 2006
Posts: 1,524
Likes: 0
Received 5 Likes on 5 Posts

Default

Install the intake manifold bolts

Tighten

Tighten the intake manifold bolts a first pass in sequence to 5 N·m (44 lb in).
Tighten the intake manifold bolts a final pass in sequence to 10 N·m (89 lb in).
Old 09-23-2007, 10:24 AM
  #8  
ЯєŧąяĐ Єl¡m¡иąŧøя ™
iTrader: (18)
 
orangeapeel's Avatar
 
Join Date: Nov 2004
Location: Justin, TX
Posts: 16,083
Likes: 0
Received 4 Likes on 4 Posts

Default

Moving to Internal....




All times are GMT -5. The time now is 03:11 AM.