Polyutethane Upper Motor Mount howto
Thread Starter
Staging Lane
Joined: Mar 2010
Posts: 73
Likes: 0
From: Utica, NY
Polyutethane Upper Motor Mount howto Hi,
I was looking around for a good howto on installing a new polyurethane upper motor mount and I wasn't able to find everything I was looking for in one place, so I put something together myself:
http://www.wesleydean.com/polymount/
Please let me know what you think or if you've any suggestions or if I'm just way off in anything I wrote or if the page load time is unacceptably low.
I hope this helps someone out.
Thanks.
Wes
I was looking around for a good howto on installing a new polyurethane upper motor mount and I wasn't able to find everything I was looking for in one place, so I put something together myself:
http://www.wesleydean.com/polymount/
Please let me know what you think or if you've any suggestions or if I'm just way off in anything I wrote or if the page load time is unacceptably low.
I hope this helps someone out.
Thanks.
Wes
Last edited by wesdean78; May 3, 2010 at 05:07 PM. Reason: corrected title
My was a bitch to take out,putting it in was a lil easier
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
Staging Lane
Joined: Mar 2010
Posts: 73
Likes: 0
From: Utica, NY
My next project is to take a look into Strut Tower Braces. I'll do a write-up on that too when I get there.
My only regret is that I wish I would have taken photos and did a write-up when I did the CAI, downpipe, resonator delete, and cat-back.
Wes
Last edited by wesdean78; May 4, 2010 at 06:53 PM. Reason: whoops..
Thread Starter
Staging Lane
Joined: Mar 2010
Posts: 73
Likes: 0
From: Utica, NY
The mod wasn't mind-blowing in terms of it's change in the dynamics of the vehicle; then again, I bought my polymount for like $35 on here, so I didn't expect much. My hope is that while each change is only a little improvement, they all add up in the long run.
Wes
I just feel a little more -thump- between gear shifts. It's not much of a difference.
The mod wasn't mind-blowing in terms of it's change in the dynamics of the vehicle; then again, I bought my polymount for like $35 on here, so I didn't expect much. My hope is that while each change is only a little improvement, they all add up in the long run.
Wes
The mod wasn't mind-blowing in terms of it's change in the dynamics of the vehicle; then again, I bought my polymount for like $35 on here, so I didn't expect much. My hope is that while each change is only a little improvement, they all add up in the long run.
Wes