OBX Headers and cutout installed
Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
OBX Headers and cutout installed I got some OBX Racing headers and a Badlanz 3" electric cutout a couple weeks ago
I also got 6' of stainless 3" pipe, Denso plugs, NGK tr6ix (one range cooler), extended front O2, and Stage 8 locking header bolts. I planned on running the 3" to the first bend and reduce it to 2.5" to hook into what is left of my Magnaflow cat back.
here are the pics.
front
rear
I also got 6' of stainless 3" pipe, Denso plugs, NGK tr6ix (one range cooler), extended front O2, and Stage 8 locking header bolts. I planned on running the 3" to the first bend and reduce it to 2.5" to hook into what is left of my Magnaflow cat back.
here are the pics.
front
rear
Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
exhaust work after installation of the headers.
on the ground
I was really happy with how well the cutout fit right against the bottom of the car. Almost like it was made for it. I was worried when I got it that it was going to hang way down but it couldn't have asked for a better fit.
on the ground
I was really happy with how well the cutout fit right against the bottom of the car. Almost like it was made for it. I was worried when I got it that it was going to hang way down but it couldn't have asked for a better fit.
Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
I only have a couple videos as of now but here they are.
Open headers right after install
a little more clear video of open headers
Open and closed cutout
that look on your face when you start your car for the first time with open headers
Open headers right after install
Open and closed cutout
that look on your face when you start your car for the first time with open headers
Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
with the cutout closed it is actually quieter than with my old setup with a catless hogan downpipe. with the cutout open since it is right on the floor board it definitely is something you notice haha. I like it though if i get sick of it i can just close the cutout and its sounds like nothing in comparison.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Thread Starter
TECH Enthusiast
Joined: May 2011
Posts: 518
Likes: 0
From: Iowa
Thank you. Nice. I love it so far. I have Magnaflows too and almost have 3 inch all the way back. I extended my 3" to the first bend and might run it around to the Y later on.
