Engine died during dyno and won't restart!
#22
TECH Addict
iTrader: (6)
Join Date: Nov 2001
Location: Tampa, Florida
Posts: 2,099
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I'm going through similar chit right now
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
My car will start up fine sometimes and then not at all.
I'll be driving down the road and it will just shut off without warning.
Not my crank sensor.
I know it's electrical SOMEwhere but we're having a hard time finding it. Now I fried the starter when it wouldn't start at ALL this past weekend.
Let me know when yo figure yours out.
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
![Sad](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_sad.gif)
My car will start up fine sometimes and then not at all.
I'll be driving down the road and it will just shut off without warning.
Not my crank sensor.
I know it's electrical SOMEwhere but we're having a hard time finding it. Now I fried the starter when it wouldn't start at ALL this past weekend.
Let me know when yo figure yours out.
#24
TECH Addict
iTrader: (6)
Join Date: Nov 2001
Location: Tampa, Florida
Posts: 2,099
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
FINALLY! After almost 2 months of nagging aggravation!
Crank position sensor wire was MELTED onto the surrounding wires from the heat of the big-a$$ headers.
It appeared that it was an issue that has progressed over a decent amount of time; and now it's just been shorting out the car.
FINALLY getting this problem fixed. Good luck with yours.
Thought I'd post up in case you have a similar electrical short somewhere involving a pinched PCM wire.
Crank position sensor wire was MELTED onto the surrounding wires from the heat of the big-a$$ headers.
It appeared that it was an issue that has progressed over a decent amount of time; and now it's just been shorting out the car.
FINALLY getting this problem fixed. Good luck with yours.
Thought I'd post up in case you have a similar electrical short somewhere involving a pinched PCM wire.
#25
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
FINALLY! After almost 2 months of nagging aggravation!
Crank position sensor wire was MELTED onto the surrounding wires from the heat of the big-a$$ headers.
It appeared that it was an issue that has progressed over a decent amount of time; and now it's just been shorting out the car.
FINALLY getting this problem fixed. Good luck with yours.
Thought I'd post up in case you have a similar electrical short somewhere involving a pinched PCM wire.
Crank position sensor wire was MELTED onto the surrounding wires from the heat of the big-a$$ headers.
It appeared that it was an issue that has progressed over a decent amount of time; and now it's just been shorting out the car.
FINALLY getting this problem fixed. Good luck with yours.
Thought I'd post up in case you have a similar electrical short somewhere involving a pinched PCM wire.
Although I haven't seen anything obviously melted yet, I'm thinking possibly I have some fried wires too.